Bondtech Extruder 3d models

This is a remix of Wundel's Ender 3 Direct Drive conversion kit, showcasing impressive promise, but unfortunately, two negative comments arose - one concerning the oversight of a spot to tie cables and another regarding tilting the 5015 fan at 45...

Check out this massive upgrade for your 3D printer: https://www.thingiverse.com/thing:3202192 - Gigante's original setup has just gotten a huge boost with the volcano nozzle and fan duct combo. Ditch those restrictive fans and take your prints to new...

This clip securely fastens BLTouch / 3D Touch bed leveling wires and fan wires in place, keeping them from flailing around during printing sessions. Updated 06Aug19 - File Rev. 3 - Both ends of the clip now have identical shapes without...

This clip helps to secure the BLTouch / 3D Touch bed leveling wires (even fan wires) and prevents those wires from flailing around while printing. Updated 06Aug19 - File Rev. 3 - Made both ends of the clip the same shape without losing functionality....

By installing it in the ball hole, you create a smooth, unobstructed path for the filament to follow without requiring reprinting the entire extruder body. This part prints flawlessly on its own, without supports, and can be used with any type of...

This is a rapid setup guide for attaching a Bondtech BMG extruder to the outstanding direct-extruder from Jasonatepaint, which may also be suitable for other directly-mounted extruders. The extruder attaches solely via the groove-neck, requiring...

This is an updated version of the original document, designed to position the BL touch in a completely upright orientation.

This is a remix of Drivinator (with cable chain mount) for Ender 3 Pro, to use in conjunction with Hero Gen5 fan. There are 2 stl files: the only difference is that v2 has the motor located 4mm more on the left, so that a BMG clone could be mounted...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This is a remix of Drivinator (with cable chain mount) for Ender 3 Pro, to use in conjunction with Hero Gen5 fan. There are 2 stl files: the only difference is that v2 has the motor located 4mm more on the left, so that a BMG clone could be mounted...

The distance between the bondtech extruder and the heat break is really minimal, but put inside a small (around 23mm) PTFE tube inside the bondtech/heat break *clearance*. ### Printing settings There is no need for using supports. Use the print...

... . I found that thing 4656838 did not fit with a genuine Bondtech BMG 1.75mm extruder, more specifically, the filament exiting the sensor did not align with the extruder filament entrance. ... I corrected the alignment using Tinkercad.

This is a hastily assembled mounting plate designed to hold the Bondtech Mini/DirectDrive extruder securely in place on a standard Prusa i3/Rework/Wilson 4 hole X carriage. ...I obtained the necessary hardware for this compact and efficient small...

Here's what sets it apart: * It works seamlessly with the Bondtech (BMG) Mini Geared Extruder and its friends. * This adaptable connector easily converts any BMG extruder to accept a 6mm PTFE bowden-tube via a smooth push-fit. * It interfaces...

I used several key components in this build: * A BMG extruder * An E3D V6 hot end * BLtouch for precise temperature control * A 50x50x15 fan for optimal airflow Additional parts include: * RJ45 Ethernet Connector Breakout Board with LED and screw...

Minor evolution and refinement of the 50mm design. I decided to test this design using one of the best direct drive extruders available in the 45mm world - the Bondtech MK2-MK3 (full kit) upgraded extruder made for Prusa:...

This is a rapid solution mounting plate to hold the Bondtech Mini/DirectDrive extruder on a typical Prusa i3/Rework/Wilson 4 hole X carriage. I bought the hardware set for this superior small extruder at MWRRF and built this quickly to get it mounted...

Extruder clip designed for a Prusa MK3s-style Extruder with a Palette 2 (Pro). ...Includes a slot for the rubber grommet.

Converting AnetA8 to a Caribo/Zaribo with a BMG extruder clone. Needed an endstop bumper. ... Testing.

... a single PTFE slip cavity at the bottom. However, this particular configuration is only practical if you're running your extruder in direct drive mode and have already inserted the hotend's PTFE into the extruder for use as a filament guide.

... from 0.63 to 0.8 so a GT3 Belt will fit snugly. - Enlarge and clean up the Cutouts for M3 Nuts, expanding them from 5.35 to 5.6mm, and extrude the surface so it becomes one smooth area because I experienced issues with the nuts fitting properly.

... correctly with everything mounted. Offset: #define NOZZLE_TO_PROBE_OFFSET { -37, 41, 0 } ---Original Credits: This is an addon for an 18mm sensor for FetteWorst's A8 direct extruder X-Carriage Original: https://www.thingiverse.com/thing:3369720

The existing BMG direct drive bracket was modified in Blender for a center drive LGX metal extruder. The metal gear LGX is currently a popular mod on the stock Anycubic Mega X. It has a different filament fitting location in the center instead of...

BOM: 1x E3D V6 (Trianglelab) 1x Bmg Extruder (Trianglelab) 1x "Pancake" Nema 17 (Trianglelab) 12x M4x12mm (original Anet ones) 9x M3 Nut 8x M3x20mm (Fans and Beltholder) 3x M3x38~mm (Extruder through carriage into Nema) 1x M3x8mm (for the Anet cable...

The originally designed component only fits perfectly on genuine Bondtech extruders. The Bondtech extruders have a width of 33mm, whereas clones measure 34mm in width. Thanks to TypQXQ for providing the Fusion file, making the modification relatively...

If you want to upgrade to the Bondtech MK3S extruder and pair it with the MMU2S, Joe Prints' IR sensor holder design is a great choice. However, keep in mind that this design is specifically for the Bondtech MK3 kit, so you'll need a different top...

This is a tool designed to work seamlessly with either genuine or clone Bondtech BMG extruders. I created this after having two clones that needed to be integrated into a single unit, and thus the chimera was born. To assemble this piece, you will...

Updated 3D printer extruder from Bondtech. ...Available in SLDASM, STP and IGES format.

Updated 3D printer extruder from Bondtech. ...Available in SLDASM, STP and IGES format.

All parts are available as a full kit here: https://www.aliexpress.com/item/Drivegear-kit-1-75-extruder-dual-gears-kit-Btech-upgrade-for-extruder-for-Prusa-i3-3d/32904209624.html And the drive gears kit is also available here:...