CPAP headboard clamp 3d models

CPAP Headboard Clamp for 50mm Thick Headboard and 15mm CPAP Tube with 18mm Outer Diameter Materials: 1x 608 Bearing for Smooth Rotation 1x M5 Screw for Tensioning Against Headboard To Assemble: 1. Use the M5 screw to clean up internal printed...

A swivel clamp designed specifically for attaching CPAP machine hoses to bed headboards (up to 30mm thickness) requires these components: one tube clip, one pin (either press-fit or hot glue), two screws (scaling may be necessary depending on printer...

A swivelling clamp with extension arm to attach the hose of a CPAP machine to the headboard of a bed. This is a remix / redesign of https://www.thingiverse.com/thing:47244 Other parts that fit the original will fit this also. Changes to the...

This is a remix of the bed frame clamp for headboards up to 85mm. Need the others parts from the original design. Print in orientation as provided. I printed the clamp with a 0.4mm nozzle at 0.2mm layer height. ... ORIGINAL DESIGN:...

This is a remix of the bed frame clamp for headboards up to 52mm or 2 inches. Note that the threads are different than the original so you will need to print the included screws. Use the short screws for headboards roughly 45mm (1 3/4") and wider.

This clip secures a CPAP hose to a turning headboard, permitting effortless rotation. ...Engineered specifically for use with the ResMed S9 Climateline hose and designed to accommodate a 28mm-thick headboard.

Headboard holder for ResMed AirMini CPAP machine. My headboard is a hair over 30mm wide so I modeled this for that. Note, the supports on my print failed so the picture is with a lot of glue while I wait for more black PLA to arrive from Amazon.

A simple bracket to route a CPAP hose along the top of an IKEA Malm headboard. The back side that holds the hose is open to allow for easy removal. There are 2 version, one is designed to go around both sides of the headboard while the other is...

... the clamp. I used OVERTURE filament because of it's strength tendencies over other PLA's. You can resize to anything you want, but right now it's designed for clamping standard size cpap hose ends. ...I believe it's around 29 mm.</p> Category: DIY

I filleted most of the edges to make the hook smooth to the touch.The holder should be printed on its side and requires a brim to get good bed adhesion due to the fillets.I installed the holder with a 3M Command Strip on the rear leg so that it's...

... OVERTURE filament because of its exceptional strength compared to other PLA options. You can easily resize the design to suit your needs, but it's currently tailored for standard size CPAP hose ends, which are typically about 29 mm in diameter.

This clamp is used to prevent the pulling of the CPAP machine off of your bed side stand when turning over in your sleep. Mounting should require two small self tapping wood screws to be screwed in to the wood of your bedside stand. ...Simple pipe...

CPAP Hose Holder Clamp (22mm) Specifically Designed to Fit Sleighbed Headboards with a Radius of ~44mm and a Front Tangent Angle of 30 Degrees. Printed in PLA at an infill of ~15%, this clamp can be easily reshaped by submerging it in hot water or...

CPAP

I bumped up its size by 110% so it would snugly fit onto a 50mm wide sleigh bed frame. ...I also downsized the tube clamp to accommodate my 17mm diameter CPAP tube with ease.

A Clamp for Securing Two 19mm cPAP Tubes Together Use this clamp, for example, to keep bowden cooling tubes vertical on a bowden-cooled Kossel effector: https://www.thingiverse.com/thing:2884959. You will need zip ties to hold the clamps together...

A clamp for securing two 19mm cPAP tubes together, e.g., for keeping the bowden cooling tubes vertical for my bowden-cooled Kossel effector: https://www.thingiverse.com/thing:2884959 You'll need zip ties to hold the clamps together. ... Includes 4 6mm...

Remixed to add a hose clamp to my IV stand CPAP Station The stand I have: IV Stand Floor Stand, Pitch-It, 2-Hook Three Leg, 30007-012 - Sold by: Pack of One https://www.amazon.com/dp/B07X9VSRK5/ref=cm_sw_r_apan_glt_fabc_VCC9M83KNBFFSCT7SN3A

Remixed to add a hose clamp to my IV stand CPAP Station The stand I have: IV Stand Floor Stand, Pitch-It, 2-Hook Three Leg, 30007-012 - Sold by: Pack of One https://www.amazon.com/dp/B07X9VSRK5/ref=cm_sw_r_apan_glt_fabc_VCC9M83KNBFFSCT7SN3A

I wanted a clamp that could be screwed, or stuck with 3M tape, that could fit multiple sizes of hose There is no reason you couldn't use this for any tubing of any size.. ... Everything is customizable

This adjustable clamp needs to fit multiple hose sizes without restriction; it should seamlessly accommodate tubing of all dimensions. What's more, every aspect of this design is fully customizable. Instructions are simple: use this versatile clamp...

I used some rubber pads on the clamp side to protect the bed. Suggest printing with at least 4 perimeters, you may need more depending on the headboard. It helps preventing the part from flexing and loosing once clamped down. ...Infill i did 20%.</p> ...

My cpap mask didn't apply enough pressure on my nose, so I printed this spacer that pushes the mask into the nose further.

... using at least four perimeter layers. Depending on the size of your headboard, you might need even more layers to prevent the part from bending and shifting when clamped in place. ...A moderate 20% infill should also help with structural integrity.

My cpap mask didn't apply enough pressure on my nose, so I printed this spacer that pushes the mask into the nose further. ...Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .1 Infill: 100 Filament: Overture...

Keep your CPAP tubes securely locked together at night to prevent them from coming loose while you sleep. ...This adapter is designed for use with both Philips Respironics System One tubes and Philips DreamStation tubes, ensuring a seamless connection...

This mitten is designed to divert excess air and the "anti-panic" from cpap machines used to prevent apneas. Since sleeping with a partner can be quite bothersome when blowing excess air, especially in winter, this should be helpful. ...By the way, I...

The original 19mm tube clamp, found at http://www.thingiverse.com/thing:47244, was altered to accommodate a 22mm tube.

... of the clamp to make it stronger and added a small platform on top. This modification has worked flawlessly, even with PLA material. The clamp has been used in conjunction with an Asus tablet, which is significantly heavier than a Nintendo Switch.

Customized version of https://www.thingiverse.com/thing:2772799 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2772799