Cable comb for GPU 86 pin 3d models

Customized version of https://www.thingiverse.com/thing:2780211 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2780211

Customized version of https://www.thingiverse.com/thing:2780211 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2780211

Get Your Cables Organized in No Time with This Handy Clip! ...Designed Specifically for Those Frustrating 3.4 MM Cords, Say Goodbye to Tangles and Knots! Want More? ...Check Out My Other Innovative Designs Today!

This is a remix for credit see the creator, I've just redimensioned it.

This is an adaptable diffuser designed for Radeon's GPUTach on video cards, specifically tailored for Vega models. It also fits the Fury X, with both variants sharing identical dimensions but distinct LED configurations. The exact range of compatible...

I crafted this bespoke external graphics processing unit stand for my high-performance gaming PC using a custom 2020 profile design, and I'm thrilled to share it with you!

This is a support for a Nvidia RTX 3090 Card to be used in a Lenovo P920. ...Since it's in a cold air flow, you can print it in PLA and it shouldn't get soft.

It should be rather difficult for this to slip out since it would need to back-out quite a distance.Get 25% off CA Filament by using the following link: https://loox.io/z/N1WXkAVWoEVGA logo was extracted from https://www.thingiverse.com/thing:2868836...

It should be rather difficult for this to slip out since it would need to back-out quite a distance. ... Get 25% off CA Filament by using the following link: https://loox.io/z/N1WXkAVWo EVGA logo was extracted from...

Hello, I decided to remix this project because I was looking for a vertical outlet rather than a horizontal one. To achieve that, I split the part in the middle into two separate sides, which now feature 90-degree outlets. ...If you'd like to improve...

Fan ducts for deshrouding a Gigabyte RTX 3070 Eagle OC in a Ncase M1. Other models might also work. ... This is designed to be used on Noctua 120 mm fans as it relies on the rubber edges to be held in place.

On my lack enclosure I use a ribbon cable to connect my Raspberry Pi to my touch screen running Octodash.  I needed clips to mount the ribbon cable to the bottom of the lack table.  I printed them in PETG because it needs to be flexible for...

This is a usual comb design, with two sections with different tooth spacing, one shorter and the other wider. It is printed in PLA and has been tested to be quite flexible, tough and serviceable. It is quite large in size and prints in about 2...

Your workspace is now clutter-free. ...This advanced organizer ensures that all your cables are neatly arranged and within easy reach.

Printed in ABS, layer 0,2mm. ...the height of the clips is 3mm. I've made 2 type of hole, 3,2 and 3,5 because the accuracy of the printer. Hope it likes you :) 12x3 in my case is necessary because in the 24conn there are some double pins.

I added a hole for screw

... ...The specifications used in this customization include 10 columns, 5 side columns, 5 end columns, 40 width columns, a height of 30 for the length, 5 for the ends, 5 for the head, and 5 for the width. ...The model was generated with $fn set to 10.

Piece to hold the flexible tape of print head connections securely in place. ... Two versions exist: one for chamfered head screws and another for flat screws.

(see photos to understand...) (For exemple for a 3.3cm total wide safety pin (standard) so 20mm of "not moving part" > scale stl to 89% , no support , no raft > go for 7 minutes of printing !) The printing time is so short , even with high...

... 5 to the right (c_s), 2 at the end (c_e), and 30 at the start (c_w). It has a height of 5 (h_l) on the lower side, no upper height (h_e), 25 for the head (h_h), and 5.0 for the width (h_w). ...The model was created with 10 faces ($fn) detailing.

... http://www.thingiverse.com/apps/customizer/run?thing_id=89532. ...For this design, the specifications were set as c_n = 10, c_s = 5.0, c_e = 5.0, c_w = 40, h_l = 30.0, h_e = (left empty), h_h = 25.0, and h_w = 5.0. ...Additionally, $fn was set to 10.

open cable combs for 3mm sleeved PC cables if you appreciate this please support me and leave a tip? ... https://www.paypal.com/paypalme/gkoolmodz

open cable combs for 2mm sleeved PC cables if you appreciate this please support me and leave a tip? ... https://www.paypal.com/paypalme/gkoolmodz

open cable combs for 4mm sleeved PC cables if you appreciate this please support me and leave a tip? ... https://www.paypal.com/paypalme/gkoolmodz

surface mount pc cable comb for 40pin 4mm braded cable

... to have not printed this particular one yet, as I think a brim might be a good idea. They're quite large, so feel free to experiment with making them smaller. Thanks go out to the awesome folks who created the files I merged together for you!

It showcases an ancient European pattern that dates back over a thousand years, inspired by a real-life comb. I've included multiple iterations of my designs for you to use. The design was created using Fusion360 and comes with STL and .f3d files...

Comb

comb

I had a hard time printing the original, so I decided to redo the whole thing so it could print better it still is not as good a tool as one would hope, as spacing the wires wide enough for plastic dividers to be in between them makes them unsuitable...