Drag Chain 3d models

This 10mm x 15mm Cable Drag Chain Link is available at MakerParts store for purchase. The link is a part of a cable or wire system, and one meter of it can be bought from their online store. You can find the product under "Cables & Wires" section on...

https://www.thingiverse.com/apps/customizer/run?thing_id=915487 Female Mount for 15x10 Drag Chain Instructions Using the following settings: link width = 15mm shell thickness = 1.8mm number of links = 2 anti-stick coating = 0.15mm part selection = 2...

... this project instead of making it yourself, you'll find it listed here: https://pwncnc.com/purchase. Our Chain Guide set at PwnCNC is an outstanding way to gain control over those drag chains. ...It far surpasses double-sided tape in performance.

... ... If purchasing is your preference over making it yourself, you can find this item listed here: https://pwncnc.com/purchase. Our Chain Guide set gives you complete control over those drag chains, outperforming double-sided tape in every way.

It needed a drag chain. I designed one. It attaches to the hotend carriage and the old extruder mount on the side. I have found it works pretty well! ... For this you are going to need: -4 m3x12 screws for the Side Mount -2 m3x8 screw for extruder mount...

... profile side. Edit (2017-11-19): Both frame side mounts don't really work. The drag chain tends to go up and touch X profile when low and far behind. Thinking about another easy way to do this. ... Fusion 360 file attached, feel free to use it!

IF YOU HAVE EXPERIENCED BAD LUCK WITH INDIVIDUAL DRAG CHAIN LINKS DE-LAMINATING, SPLITTING OR BREAKING, THIS ONE IS FOR YOU. I ADDED THE ADDITIONAL FILE SO THAT MORE THAN ONE CAN BE ZIP TIED TOGETHER FOR LONGER DISTANCE AXIS. YOU SHOULD PRINT IT...

The revamped drag chain end is for the extruder. It's securely fastened at the upper corner by a long bolt. I encountered difficulties directly modifying the original piece, so I opted to redesign it using OpenSCAD. To install, simply print and affix...

This drag chain support for the MPCNC Primo replaces the regular Truck Clamp.It is for the 25mm version (F) and is suitable for a 30 x 15 mm aluminium strip which can be found at your local hardware store in 1m lengths. ...(at least here in The...

These are modified,  shorter end connectors for the drag chain designed by Marius Hornberger.  There are two variants available:Variant 1 has two 3mm holes for countersinking screwsVariant 2 has one 4mm hole for a countersinking...

However because I haven't had a chance to make the model fully responsive (Fusion isn't great about variants), if you do make the change be sure toadjust the centerline back to =13.7 before exporting the motor side as the hole location moves as well...

The new mounts were created in Solidworks 2016 Print instructionsUnassociated tags: cable chain Category: Parts Instructions Use M4 x 12mm FHS and M4 nuts to attach the drag chain end to the printed mount. Use M5 SHCS & nuts to attach the mounts...

Instructions To assemble this setup effectively, you will need M4 x 12mm FHS screws and corresponding nuts to connect the drag chain end directly to the printed attachment. Next, secure the attachment itself to the Shapeoko2 machine with an M5 SHCS...

SeckitGo2 drag chain mount for a 10x11 chain. This is an exact fit to the chain below. No slop in the end point connections to the chain from the mounts. ... Perfect hole alignment with this chain on Amazon -...

A replace for the little arm that holds the vertical (bed) drag chain to the bed carriage. The holes for the chain are placed 10mm nearer the bed, so the chain shouldn't tangle with the upper aluminium extrusion. Instead of doing a simple block with...

The drag chain links and covers are all from the original files built by johnniewhiskey and I used a couple of his mounts as starting points when building the termination sections for this. Everything was built in Tinkercad. To assemble, you'll...

Three M5 holes on the top surface can be used for attaching additional mounts or aluminium angle to support your drag chain. Extra M3 holes on the front and side faces offer flexibility for adding accessories or securing cables with a cable tie (as...

Introducing an uncomplicated attachment designed specifically for standard drag chains, seamlessly compatible with NEMA 17 motors.Installation is a breeze. Begin by orienting the open section upwards, aligning it with the motor connector. Gently...

Realizing that my original setup didn't place the drag chain at its optimal center position on the V-slot profile, I designed a second version that's intentionally offset to match my existing configuration. This new design features a more secure...

Remix of the Drag Chain - Cable Chain - Ender 3 by diogosantos88 June 26, 2019 which has a 50mm and 40mm carriage mount. This has been modified for the TTP which has a 45mm center spacing for its carriage. I also created a way to attach the chain to...

Note that the file is currently designed for compatibility with the Halo, in order to make a standard extrusion version simply change the offset distance of the construction plane "Drag Chain Center-Line (13.7=Halo, 19.7=standard)", found in the root...

This is a set of drag chain mounts for the 25.4mm (1") MPCNC Primo by V1 Engineering. The brackets are designed to hold a length of aluminum angle to support the chain links. The length of this angle will be determined by the size of your machine. ...

17Feb2017 -- Added mounts for 40x15mm drag chain per qbvbsite's request. I haven't tested it or anything, but it seemed to fit his well. "Remix" of ooznet's Y drag chain mount. Basic dimensions are all the same, except re-drawn from scratch and...

I used these melt-in inserts from Mcmaster-Carr for the drag chain attachment and bracket attachments: https://www.mcmaster.com/92395a113. I've also been told that this melt-in option works well: https://www.mcmaster.com/94459a290. I have printed...

Drag chain holders for the Artillery Genius printer.Drag chain:UK: https://www.amazon.co.uk/YOTINO-Plastic-Towline-Printer-Carrier/dp/B07S6LW7BKDE:...

Drag chain: UK: https://www.amazon.co.uk/YOTINO-Plastic-Towline-Printer-Carrier/dp/B07S6LW7BK DE: https://www.amazon.de/YOTINO-Schleppkette-Kabelführung-Kabelschleppkette-Energiekette/dp/B07S6LW7BK UPDATE: I drilled a hole into the case so the...

I finally have it, the Ender 3 Drag Chain that works on the Ender 3 Max. I will upload it here so everyone else that buys that printer doesn't have to go through the same pain I did. It just snaps right on in there, but it is a one way trip, oh...

Drag chain holders for the Artillery Genius printer.Drag chain:UK: https://www.amazon.co.uk/YOTINO-Plastic-Towline-Printer-Carrier/dp/B07S6LW7BKDE:...

I originally designed the drag chain for my 3d printer following this tutorial https://www.instructables.com/Fully-Functional-Drag-Chain-Fusion-360/ In theory the links should have a 40 deg range of motion, there are 42 of them and the internal...

It needed a drag chain. I designed one. It attaches to the hotend carriage and the old extruder mount on the side. ...I have found it works pretty well! For this you are going to need: -4 m3x12 screws for the Side Mount -2 m3x8 screw for extruder mount...