Enclosure for Digital Temperature Controller 3d models

I utilized the Digital Auber Temperature Control to construct a Powder Coating OVEN. I saved my SW2016 files on GrabCAD for future use in other projects. ...The outer dimensions and weights are accurate, while the inner part features are omitted from...

It needs a W3230 temperature controller, but you can buy one from eBay or Banggood for loose change pretty much. The case fits the T-360-12 power supply, and clamps fit 1x1.75mm wire. I'm thinking of printing a flexy seal to fit under it, but it...

I crafted this enclosure specifically for my temperature switch, which I use to regulate fan usage in my solar panel inverters. The design is straightforward - it's meant to be enjoyed. Print Settings: Printer Brand: Wanhao Printer: Wanhao...

An enclosure for the DSO138 oscilloscope with room for a 9V battery.

... the Socket On. ... For a 12V Digital Thermometer from Amazon, simply print this case on both sides, flip it over and glue the socket in place. 55mm x 40mm x 36mm is the exact size of this case. ... Get it here: https://www.amazon.com/dp/B00I1B54DI

An enclosure for the DSO138 oscilloscope with room for a 9V battery. Print Settings Printer: TronXY X5S Rafts: No Supports: Yes Resolution: 0.25 Infill: 15% Filament: Generic PLA Any Category: Electronics

EN: Case for 12V Digital Thermometer from Amazon - For Print Flip to Front and glue the socket on DE: Gehäuse für 12V Digital Thermometer von Amazon - Zum Drucken auf die Frontseite dehen und danach den Standfuß ankleben 55mm x 40mm x 36mm LINK:...

Reef Tank Temperature Controller Enclosure for Pi Zero Based System. A Simple Housing Solution That Accommodates the Mounting of Pi Zero and One 3.5mm Audio Jack. Power Is Supplied by the Pi Zero's Power Supply, Specifically a Micro USB Port...

Small Enclosure Temperature control Box based on a w2809 thermostat(46mmx26.5mm) and a small 12v power source(85x57x33mm) like Orno OR-ZL-1631 Testprint STL -> Just resize Z to 3 or 4mm It has no backplate V2 STL PSU dimensions (89x59.2x33.5mm)

I designed this adapter for the enclosure I've made so that I can control the temperature with an arduino nano and keep the printing fumes smell outIt is designed similar to an axial compressor stator since it goes from a large diameter to a smaller...

as per AJM1's design, i just added on a couple of tabs so I can mount it.

W1209 Temperature Control Housing

STC-1000 is a nice little temperature controller that can be used to control both a heater and a ventilation in an enclosure. 12V and 220V versions are available for 10-15 EUR (Amazon) or $3-5 (AliExpress). This box is designed to be mounted directly...

I built this adapter specifically to fit inside the enclosure I created, allowing me to regulate temperature with an Arduino Nano and keep printing fumes at bay. The design draws inspiration from axial compressor stators, which transition smoothly...

... OR Experience a convenient, 3D printable one-piece enclosure for Phidget's 4-Input Thermocouple Temperature Sensor (model 1048_0). ...For more details, visit the product page at http://www.phidgets.com/products.php?category=35&product_id=1048_0.

... Used double sided tape to mount. Print Settings: Printed in Cura 0,2mm 2 Walls 4 Top 4 Bottom 20 % infill Controller can be purchased here. ... https://www.aliexpress.com/item/1005001388901396.html?spm=a2g0s.9042311.0.0.625f4c4dkHu1RL Enjoy !

Printer enclosure thermostat holder displays interior and exterior temperatures with ease. Crafted from PLA, it requires no support for a seamless build. ...To take your printer to the next level, check out these essential components: 2x Thermostats -...

This is a control panel or box for most 3D printers in an enclosure. I have it configured to hold the print chamber at 35° C and 20% humidity. I printed from PETG with the MMU2S, the front panel is available separately so it can be printed flat on...

Quick and dirty Case for RepRap.me Heatbed Temperature Controller http://reprap.me/electronic/heatbed-temperature-controller.html Three buttons are exposed, the display is tucked under a slimmer surface - with PETG it's still easily visible. Simply...

... Printed in PLA, but this design can be easily adapted to print with almost any material. Design Process: Created using Fusion 360 software, this mounting bracket and sensor holder are perfect for RioRand temperature controllers.

A basic case for for an STC-1000 (or ITC-1000) temperature controller. Prints without supports, and needs no fasteners. After printing, run the sensor wire out through the back hole of the case and run your power and device wires in through the...

This is a case study for the ESP32-Wrover PID temperature controller, also known as PIDKiln. I designed it specifically for my ceramic and jewelry kiln, with the hope that others will find it useful as well. The components used in this project...

A basic case for for an STC-1000 (or ITC-1000) temperature controller. Prints without supports, and needs no fasteners.</p> <p>After printing, run the sensor wire out through the back hole of the case and run your power and device wires in through...

I made this little enclosure for these cheap PWM controllers you can find at places like Ebay, Banggood, and Aliexpress. This enclosure has tabs that allow you to mount it to the Rubbermaid FastTrack rail, or you can just cut them off; I don't care.

... If she stores her food in a temperature-controlled unit, it can provide both heating and cooling capabilities since it features both a refrigerator and a heater. The egg symbolizes the food being stored, while the house signifies the storage space.

https://www.thingiverse.com/apps/customizer/run?thing_id=121479 Options in Use: Wall Height: 1.4 Units Rim Wall Thickness: 1.4 Units Screw Head Width: 3 Units Base Depth: 95 Units Bolt Size: 1.5 Units Hole Diameter for Bolts: 2 Units Rim Wall...

Digital Thermometer MountI designed this simple case for a standard digital thermometer to be used with the 3D printer enclosure from enclosurelab.comThe excess cable hides in the back. Great for monitoring the temperature of your printer box. ...Since...

I remixed this enclosure to fit a second power outlet so it can cater to teh Sonoff Dual R2. ...Also there's a hole to route sensor cables through to connect a DHT22 sensor as shown in this tutorial...

Surface mount for Planar/Autoterm 2D Digital Controller.

Digital Thermometer Mount I designed this simple case for a standard digital thermometer to be used with the 3D printer enclosure from enclosurelab.com. The excess cable hides in the back. Great for monitoring the temperature of your printer box.