FIOS Router Mount 3d models

I devoted several hours to finding a precise match for my Ryobi trim router, only to discover numerous designs that nearly met my expectations but ultimately fell short. ...I then embarked on a meticulous examination of all potential designs, carefully...

This is for the T Mobile trash can router, the router gets very hot, especially when using the onboard WIFI, and when it gets too hot you can see performance diminish, so I designed this to be used with a 120mm fan, the fan slides easily into the...

Simply slides in at the angle.Print them out and slide them on at the angle (45degree at the thinest side curve)They should rest over the rubber feet of the router.Mark position on the wall, remove brackets and screw them to the wall and once again...

Store up to 7 small and 4 large router bits in this under-desk router bit storage.There are versions for:8 mm bits6mm bits¼ inch bits4 x ½ and 7 x ¼ inch bits mixed  My updated version 2 provides space to add 2 times a 2x16mm magnet to keep the...

Needed a stable shelf for my Google WIFI router since it's in an area I will be working in and don't want to keep knocking it off a flat shelf. Downside is you have to unlplug it before putting it on the shelf or removing it. ... I may revise it...

The only spot where I could set up the Xiaomi router was indoors. However, the 5GHz Wi-Fi signal struggled to penetrate the concrete wall, resulting in subpar connectivity. ...After some experimenting, I discovered a solution to isolate the antenna and...

This is the wrong way to do this, but it's much cheaper than buying an electronically controlled Router Speed Controller. This will require some significant fitting. Filing that little knob is a pain to measure. Made for a RSC-9400, controlling a...

This adapter is designed to replace the 52mm spindle on a CNC router with a laser module, effectively converting it into a laser engraver. Print Settings Printer Brand: Printrbot Printer: Simple Black Supports: Yes Resolution: 0.25 Infill: 100 ...

ASUS TUF-AX5400 have no built-in wall mount holes. ... Sharing simple mounts 2 bottom and 2 sites mounts. ... Designed in 15 minutes :).

Because Netgear never released an official Orbi mount suitable for the SXR50 Orbi, I designed one myself. ...This mount can easily be mounted to a wall and has a cable passthrough.

This project was made to adapt my CRP4896 so that I could hold a e3D V6 in the EVS Bosch 1617 Mount. ... Works great...!

This is an adapter for mounting Zyxel EX3301-T0 modem to the wall. ...The adapter provides enough space (5.5cm) between the modem and the wall to make all cable connections on the backside.Print it with supports for mounting heads.

... either with or without a dust boot tool. This allows for maximum flexibility and adaptability. The result is a sturdy mount/holder that can withstand even the most demanding tasks, such as working with high-strength aluminum alloys like AW 7075.

Rugged R24012 spindle holder designed specifically for Root 3 CNC machines, engineered by modifying the standard 65mm mounting system. ...Constructed from high-quality PETG filament, printed at a moderate 50% infill density.

For more stability I have merged the MPCNC Tool Mount with a Makita Tool Holder. It fits with the 25mm version (metric). This Tool Mount can be used for MPCNC Burly and also for MPCNC PRIMO. Using 2 parts connected via screws resulted in a "somehow...

Human here, just uploaded a fresh clip https://www.thingiverse.com/thing:3216341 I flipped this design to ensure the cable points upwards for ceiling or above-mounted installations, also beefed up the support and I'm tweaking the piece beside your...

... ribs to prevent them from cracking after only a few hours of use. ...I also integrated a dedicated holder for the vacuum hose, strategically cutting out access points and recesses in the body to allow easy screwdriver access to the mounting screws.

... metal case that's impossible to drill into. ...To avoid attaching the entire device to it permanently and still make it removable, I came up with this glueable imitation of a screw head that lets me use the original mounting points of many devices.

I made this to mount the Geckodrive G540 Stepper Motor Driver in my control box. ...I decided to change the design and put a 0.500" clearance between the bottom of the controller to help with cooling since i am going to pt a fan blowing on it. Screws...

This mount routes cables along the bed to safeguard them and minimize rear space requirements on the Ender 3. It's designed for use with other components listed here, including cable sleeves and an electronics enclosure. A fixed bed is necessary, so...

... to position a fan directly above it. Mounting screws for the driver are M3 screws secured with nylock nuts. ... Print Settings: Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: No Supports: No Resolution: .300mm Infill: 100%

The openscad file was included so you can adjust the spacing between holes and height, yet I retained the original hole arrangement for the mount because it felt like a more solid layout. ...Currently working on reworking this to attach my shop vac to...

This mount re-routes the cables along the bed to better protect them and to shorten the space necessary at the rear of the Ender 3. It is intended to be used with other components that I have posted here. Namely, the cable sleeves and electronics...

This simple mount helps to store the Makita Guide Rail Adaptor inside the Makpac, fixed on the Makpac cover. The outer size is +,1mm, so you maybe need to trim with sanding paper. But this ensures the adaptor is fixed tightly Note: This is my first...

This is a mounting bracket designed for the Starlink router. Designed so that it can be mounted upside down or on a vertical surface. ...

Designing My First Ever 3D Print To achieve the perfect fit, ensure that supports are enabled for printing across all areas. ...Although it was a snug fit, my first print successfully slipped into place; however, scaling it up ever so slightly may be...

I'm excited to see your first upload! I needed a versatile bracket to hold my switch, AP, and power supply, so I created this. I hope you enjoy it! ... Print Settings: Printer Brand: LulzBot Printer: TAZ 6 Rafts: No Supports: No Infill: 10%

A remix (thanks Brian! ...(bpopp)) in order to fit to my Root3 z-axis https://www.thingiverse.com/thing:3651483

<p>A remix (thanks Brian! ...(bpopp)) in order to fit to my Root3 z-axis <a href="https://www.thingiverse.com/thing:3651483">https://www.thingiverse.com/thing:3651483</a></p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>i3 Rework</p> <p...

Remixed to make it compatible with NEJE 30820.