Fan Mount used by Droodle for Cobblebot Mod 3d models

For installation, first ensure your E3D blower fan faces towards the back, drawing air in from this direction (refer to the provided picture for guidance). Proceed by installing the bracket and then securing the FAN in place. Enjoy the rest of your...

I found that with the original fan mount my print fan (https://www.thingiverse.com/thing:3972011) was not correctly centred with the nozzle, being about 4mm out on the Y and 5mm out on the X, so modified the original fan guide and is now all centred...

This mount is designed to fully replace the existing y-axis carriage on my printer, making way for the Chimera/Cyclops to be mounted seamlessly. The concept behind this mount was initially inspired by Repraph's ingenious design...

Can be used to add a rod to the Y axis motor to use a dual belt drive for the Y axis.

Adding a rod to the Y-axis motor enables the use of a dual belt drive system for the Y-axis.

This bracket mount is designed to slide onto the long edge of a Cobblebot Basic/Beast carriage and has two angled pockets that allow for ventilation with 5015 style blower fans (centrifugal or squirrel fan, 50mm diameter, 15mm deep). The fan angle...

The holder accommodates the Arduino board for the CobbleBot Vanguard printer, allowing for a simple and secure attachment. This assembly fits snugly under the print bed with precision-cut posts designed to securely grip the Arduino, locking it into...

A second screw hole for the PLA fan may be necessary, but initial testing indicates stability and no immediate additional support requirements. ... Recommendation: For optimal results, consider utilizing an X Carriage as shown in...

I have only modified the PCI fan mount with the cable management so I could use wider 20mm fans as that's the one I am going to use but with any requests, I can modify any other of the files and add them to the files list as soon as possible. ... Also,...

It's a mount designed to fit 4020 blower fans. ... The spacer pice helps to tight better the right fan to the mount but it can be used for both, the same pice it's used also in the hero me gen 5 4020 dual fan ducts. ...

This is an upgraded extruder-to-fan mount that pairs perfectly with your brand-new fan mount component.

... indicator is a Fowler with a 9.5mm diameter neck. Printer Settings: Printer: Cobblebot Little Monster - TinkeringOnSteroid MOD Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .24 Infill: 20% Notes: Print at your preferred comfort level.

Enhanced Cooling System - Premium Upgrade Kit for Ender3 and Standard 40mm Fans.

PLA 40mm 4056fan jet fan DIY

High-Efficiency Dual Mounting Kit for High-Performance Fans Utilize two 24V radial fans with dimensions of 40mm in width, 40mm in height, and 20mm in thickness. ...Included in this assembly are two sturdy metal components measuring 30mm in length, two...

This is a custom fan duct design specifically tailored for the Anet A6 Titan mount by Xalky. https://www.thingiverse.com/thing:2459756 The round shape of this duct enhances air distribution significantly. V5 requires resizing to 10% (or 90%...

Designed to fit a 15.5x45mm fan splitter, should fit just about any 15.5mm wide, left the tape on back so i could ignore the solder points and get smoother grip, mounts with two m3 screws, should mount on just about any extrusion.

Designed to fit a 15.5x45mm fan splitter, should fit just about any 15.5mm wide, left the tape on back so i could ignore the solder points and get smoother grip, mounts with two m3 screws, should mount on just about any extrusion. Category: DIY

I was unable to find a suitable e3D Chimera Dual Volcano hotend mount for my Cobblebot 3D printer with cooling fans, so I decided to design one myself. Based on the rough design of my previous mount, I added some holes for mounting the fans (previous...

I modified the bolt hole to accommodate an M3 bolt, choosing not to swap out the original T-nut used by the Cobblebot for endstops.

Here are a few settings I use for my own printers, modified slightly for use with the Printrbot Gear Head Extruder. I use the default RepRap Firmware configuration, but tweaked the acceleration to improve printing performance. ... 1 inch layer height...

The Case for my Full Graphics Smart Controller was printed from the http://www.thingiverse.com/thing:87250 design, which I modified by drilling out holes in the front part and installing four M3x50 bolts/nuts. To prevent interference with the...

I built it with mounting the Full Graphics LCD directly to the top of an 80x20 Extrusion using two sturdy M5x8 bolts and T-Nuts that securely hold everything in place. I utilized a 3D printed Case for the Full Graphics Smart Controller found at...

The primary reason for using this mount was that I wanted to utilize dc42's IR sensor and eliminate the original E3Dv6 cooling fan mount, which I deemed the only weak aspect of my design. The IR sensor mounts were always getting loose and rattling...

The main reason for using this mount is that I wanted to use dc42's IR sensor, with the bonus of getting rid of the original E3Dv6 cooling fan mount, which I consider the only weak part of the design (mine always got loose, and rattled around). I...

... To mount the Arduino securely, examine the screws you're using; if necessary, insert spacers between the Arduino mounting and the fan support for a snug fit. ...Soon, additional padding will replace these spacers entirely

Connect it securely to a gear, like the planetary gear found at thingiverse.com/72069, using its threaded hole designed specifically for a 5mm hex key. Secure the holder firmly to your printer with four 5mm bolts, featuring t-nuts within their...

... 80x80x25mm fan. ... Hardware i used: Sunon EE80251S3-999 (OPTIONAL) M3 heatset inserts, outer diameter: 5mm, length: 4mm (only for mounting the buck) (OPTIONAL) tinxi® 5A 75W DC Step Down Converter (https://www.amazon.de/-/en/gp/product/B01FRZVZPQ)

Adjusted a few things so it can fit the stock fan duct and fit on the bracket a little more securely. ...Love this design overall.

With this fan mount and a 50/15 blower fan attached, it will bring the internal temperature up to about 48c which is proper for drying PLA and maintaining other filaments. Just tap into the 24v power supply and your good to go. There are lots of...