FlashForge Creator Leveling Feet any MakerBot actually 3d models

The model, originally sourced from http://www.thingiverse.com/thing:180757 (with the original design thread found at http://www.thingiverse.com/thing:153807), was integrated into a replica of the plate on top of the extruders for a FlashForge Creator...

Soporte de bobinas para FlashForge Creator Pro. Se imprime la base para posteriormente añadir la sujeción de bobinas que trae de fábrica la Creality Ender 3 y sus derivados. ... Se requiere 2 tuercas M5, los tornillos se pueden usar los mismos que...

I modify this blower duct http://www.thingiverse.com/thing:560790 to fit my FlashForge Creator Pro. I used a SUNON GB1205PHV1-8AY.GN (http://fr.farnell.com/sunon/gb1205phv1-8ay-gn/turbine-50x50x15mm-12vdc/dp/1568490) with this blower duct. Do not...

For Flashforge Creator compatibility, follow these steps: remove support structures after printing, attach the fan mount as shown in the photos, and ensure it's higher than the nozzles. ...Use at your own risk due to the lack of electrical wiring...

@3DPrintFresno Certain filaments come with a bigger interior tube than the FlashForge Creator's current filament spool holders, so these fit onto the back of one side of the Creator's filament holders. If you have a dual extrusion model, you will...

Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 14% Filament: Renkforce ABS Black Post-Printing: If the holes come out too small, use a 3 mm drill for the screw holes and...

Leveling Feet for 3030 alu Profiles Use 3030 M5 Nuts to fix it

As I was not happy with any of the available leveling feet, especially with the thread tolerances, and inspired by the already existing variations, I designed my own modification. Easy printable on any FDM and should be also on your resin printer as...

As I was not happy with any of the available leveling feet, especially with the thread tolerances, and inspired by the already existing variations, I designed my own modification. Easy printable on any FDM and should be also on your resin printer as...

This accessory securely attaches to the side of a FlashForge Creator X by snapping into the built-in carriage mounts on either side. A hex wrench storage section fits exactly 3 standard 1/4" drive wrenches typically supplied with the 3D printer...

I recently acquired an old FlashForge Creator (with the wooden frame), but it was missing some parts - including one of the filament feeder tubes.  I'm not sure what the original ones were made out of, but I had some PTFE tube and fittings on hand...

GoPro Mount for Flashforge Creator Pro. Two arm lengths are available, 45mm and 60mm. This mount will hang from the front of the printer, with a hump in the middle to fit over the screw. (This is designed specifically for those who paid $1,200;...

GoPro Mount for Flashforge Creator Pro. This mount attaches to the front of your printer, with a raised section in the middle to fit over the screw. Designed specifically for those who invested in the higher-end model, this mount takes advantage of...

If some of your filaments have larger inner tubes than what the FlashForge Creator can handle with its current spool posts, they should be placed on the back of one side of the spool posts. Users with dual extrusion models will need to print two of...

GoPro Mount for Flashforge Creator Pro. Two downward arm lengths available, 45mm & 60mm. This mount will be attached to the front of the printer, featuring a hump in the middle designed to go over the screw that's standard on printers costing $1,200...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20 or less Infill: 25% - 100% Notes: When printing the hanger and knurled knob, add a G-code command to pause the print just before covering the captive nut hole...

This Thing offers both a replica of the top plate of the 2016 FlashForge Creator Pro (unsure whether this is different on older models), and an improved version (‘v2’ suffix). This is the part that connects the umbilical cord and the filament guide...

So I had to purchase the only lid FlashForge provides for the 2016 creator pro, which is the unibody lid. If you're not aware, this lid is 12mm too short to sit properly on top and there are no brackets to secure it in place. As a result, here's my...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

You can find them here https://www.lowes.com/pd/Hillman-3-8-in-to-16-x-3-in-Zinc-Plated-Elevator-Bolt/3722632\r\n\r\nPause the printer at either 13.9 or 14mm layer height and insert a standard 3/8 nut.\r\n\r\nThe leveling feet also come with a simple...

Weiterentwicklung des Filament Wandhalters, zu dem Ersatzhalter für den Falaschforge, Creator Pro /2

The filament arm extruder top serves as an attachment point for the tube, ensuring that it won't bump into any wiring or tubes easily. ...Lastly, there's the cover clip 2, which is a side/front cover clip, while the latch clip turn is used to secure the...

Designed these lack table feet for my LackStack to help stabilize it a bit and level it where needed. 

You could utilize the metal type rings (I forget their technical name) to help minimize the noise, but for now I have no issues and it's working great.\nAny other ideas or suggestions feel free to share, I will try to accommodate any request!\nThanks...

Mount for the Paneldue i5, it is made to replace the original LCD display of the Creator Pro 2016 and uses the same screws.

Customized Version of Thingiverse Project 193647 Created with the Power of Customizer, a Tool That Empowers Creators to Bring Their Vision to Life

Customizable Funnel Upgrade for Flashforge Extruder The flashforge extruder's interface gets a significant boost from this add-on funnel, which also helps keep the filament guide tubes securely in place. This improvement is particularly useful when...

Simple Spool Holder for the Creator Pro, I wasn't a fan of most on the site so far. ... Hardware: 1/4-20 Nut 1/4-20x3.5" Hex head bolt Hope you find them useful!

Here is the spun text: Creator Pro Spool Holder for 1kg ESUN Brand Filaments \n Customized version of http://www.thingiverse.com/thing:1108314 \n Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1108314