Gate latch 3d models

I started by sketching out the front profile, making sure all the measurements including radius' were correct, then I boss extruded the model without including the circle.

CSWA part

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters For creating this drew this out from the blueprint provide and started sketching at first the circle I did not put at the origin so make sure to do...

The material used is AISI 1020, and it has a mass of 1066.52 units.

Plugs that can be used on the model, positioned using rubber bands.

step1: sketch geometry according to the blue prints (( !! crucial !! ...- when sketching make sure the arcs are fully defined first, then make the line under the whole cut out concentric with the axis))(note) the axis point in the blue prints can be...

a tool

Solidworks Certification test

steps:1. created left edges sketch first2. added the curves, created relations and dimensions3. worked on right side of sketch4. added hole in left center of sketch5. added finishing relations with respect to the plus reticle thing6. extruded7.

Simple FreeCad Assembly

Humans can easily manipulate the locking mechanism.

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersProcedure: I started this model with the sketch from the front view. Started with the circle on the origin, then I sketched all the lines above and to...

Mass = 1067.90 gramsVolume = 135176.75 cubic millimetersSurface area = 18942.85 square millimeters______________________________________________________________________________________________________I started the sketch by making the general shape...

Mass = 1066.52

step1: sketch geometry according to the blue prints (( !! crucial !! ...- when sketching make sure the arcs are fully defined first, then make the line under the whole cut out concentric with the axis))(note) the axis point in the blue prints can be...

I used the line tool to create my shape than started to dimension everything to the correct length. I used the arc tool so i could make my curves and everything. ...I than extruded than and but a circle on the shape and cut it through the entire shape.

Individual placed in second-ranked structure.

I started by sketching out all of the straight lines and dimensioning them as such. To create the curved geometry, I used two different types of arcs. I created a centerpoint arc, using the midpoint of the long line in the bottom right as the center....

cswa

Steps:1. Started the sketch o the 40mm ark and dimensioned as I went, when I got to the corner with the two tangent arcs, I made the horizontal line coming from the 45 angle coincident with the point of the 29mm arc.2. Extruded to part width3.

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersI sketched out a circle of radius 6, and a line 18mm long on the left, and then 2 of 45degree angles, make sure the center of the circle to the bottom...

infill density: 30%Layar height: 0.2Top/Buttom layers: 6Material : PLA/PETG/ABS Support: NO

Steps:1. Started the sketch o the 40mm ark and dimensioned as I went, when I got to the corner with the two tangent arcs, I made the horizontal line coming from the 45 angle coincident with the point of the 29mm arc.2. Extruded to part width3.

I started by sketching out all of the straight lines and dimensioning them as such. To create the curved geometry, I used two different types of arcs. I created a centerpoint arc, using the midpoint of the long line in the bottom right as the center....

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters

Mass = 1066.52 gramsMake a sketch with a circle at the origin R6. Make a line to the left and underneath both 14 away. Make the left line 18 and between those a 45degree angle line. The bottom line running until a R5 circle's top. From that circles...