GoPro Adapter for Hope R4 LED Lamp 3d models

This is a makeover of Thing 2870039 to level it out and add a cutout for the microphone up front. The original creator tackled the balance issue by gluing some nuts onto the side of the case, but this mod provides a more visually appealing solution.

Base and End for a LED Lamp for your Monoprice Select Mini. Print enough of these (http://www.thingiverse.com/thing:5578) and then the end and base here. They all work together perfectly. The base has a hole for wires that run inside the...

Check out the sleek lamp design showcased in the photo of the LUNA LED reading light. This stylish accessory is designed for optimal use, mirroring the purpose of a printer's sturdy base. To ensure proper fitment, simply insert the 2 cm long...

I decided that didn't want to put more holes in my wall so I made a stand for the Hyurule Royal Family Crest LED Lamp/Sign. I wanted the stand to continue the Legend of Zelda theme, so this is a Sheikah eye symbol held up by a Fairy base. This will...

Base and tower to put LEDs in an 18cm Voronoi lamp. LED strips can be wrapped around the center pole, and there is a slot for the wire. The Cover goes on top of the Base and hides the wires form the holes near the base of the lamp. Print Settings...

The standard baseplate file only has 0.1mm tolerances and was too tight for my Prusa i3 MK3, which I attribute to using a 0.6mm nozzle. You can likely use the left post (the one with the hole for the nut) as the right post as well to minimize...

Basic shock-absorbing tripod adapter removes mounting vibrations from vehicles, aircraft cockpits, and other equipment. ...It employs high-quality foam earplugs as vibration dampeners.

I decided that didn't want to put more holes in my wall so I made a stand for the Hyrule Royal Family Crest LED Lamp . I wanted the stand to continue with the Legend of Zelda theme, so this is a Sheikah eye symbol held up by a Navi the fairy...

I built igorF2's articulating LED lamp for my office wall, but needed to adapt the lamp holder to hold the off-the-shelf GU10 fixtures I had available, which have a 28mm outer diameter. I also wanted a diffusing lampshade to spread the light around a...

For the shade, since we didn't need access for a tea lamp, I took the revised lamp shade and cut it in half and mirrored it. After some cleanup, we have a fully intact lampshade. Print the base in whatever color you want but print the shade in a...

... routing the picam ribbon cable along the gooseneck. I also have a custom mounting base for the Jansjo lamp, which can be found at https://www.thingiverse.com/thing:3327503 under the title "Stylish Mounting Base for IKEA Jansjo LED Gooseneck Light".

The Basic Tripod Adapter Eliminates Mounting Vibrations in Cars and Cockpits. ...It Utilizes Standard 21mm Length Drone Dampening Balls Available at: https://www.unmannedtechshop.co.uk/premium-rubber-vibration-damper-balls-pack-of-4/

Replacement for faulty latch on compact LED sparkler light fixture.

Stand V3 is similar to Stand V1 in terms of design, but it's meant for use with LED lamps instead of candles. The pictures are arranged in a 3x1 layout, which creates a beautiful display of light and shadow. To create your own lithophane pictures,...

Using standard electrical ducting, and some 25mm PVC pipes, you can create your own LED lamp. The feet can also sit on the edges of a glass aquarium. ...Select the opposite edge of the tube fittings when printing.

The support offers an alternative to the unattractive elastic light bracket that deteriorates over time on the remarkable Yamaha TT 600. ...This replacement enables you to attach a compact ShinYo LED rear lamp, accessible in various nations.

I have the Pazzo LED Shelf Lamp and wanted to use my USB fast charger however I was slanting due to size. ...Made this to fit around the 2 prong plug and support my ugreen charger block.

A table lamp adapter to fix a new shade. ... Print Settings Printer Brand: Deltaprintr Printer: Deltaprintr Kit Rafts: Off Supports: No Resolution: High at 0.2mm Infill: Medium at 18%

Gopro clipse adapter for ravemen holder

GoPro Adapter for Soft Mount System.

A lampshade to just put on the Chihiros LED System Serie C - C201. If you need another one for the other sizes, just write in the comments. This lamp is not getting hot, so you can use PLA for the print. Print Settings Printer Brand: Anet Printer: ...

this is a remix of "3D Printed Articulating LED Lamp" ( https://www.thingiverse.com/thing:4739055 ) and an improvement of last version that I had made. ...In version V2 the fixation lamp is improved and the thermal resistance of deformation too.

Mount an LED Lamp from igorF2's File on Thingiverse https://www.thingiverse.com/thing:2505394 This design is a remix of Johann517's screw, also available on Thingiverse at https://www.thingiverse.com/thing:1673030 To attach the lamp to a nightstand,...

In addition to the safety railings, I am adding lights under the railings and to the ceiling using LED filaments (see photos). I'll provide more about the lights in a seperate upload. Speaking of the safety railing, that is made of a strip of...

In addition to the safety railings, I am adding lights under the railings and to the ceiling using LED filaments (see photos). I'll provide more about the lights in a seperate upload. Speaking of the safety railing, that is made of a strip of balsa...

Fuocco Lightstar's LED lamp for track comes in white (215236), black (215237), and gray (215239) options. This light measures X: 1076, Y: 60, Z: 261 with a D60 H240 specification. It uses a 15W LED emitting 950LM, constructed from 14,127 polygons and...

GoPro Battery adapter to use GoPro 6,7,8 Battery for GoPro 9,10,11

Today's build is a cutting-edge Arduino controlled LED lamp featuring WS2812B LEDs, equipped with a capacitive touch button that seamlessly transitions through modes and a piezo buzzer that alerts users to its detection of the buttons' touch. This...

It's 20% larger and comes equipped with a holder for LED candles that fit snugly inside, up to about 41 mm in diameter. Printed with clear transparent PLA, I've managed to make it even more see-through by applying XTC-3D. Unfortunately, I don't have...

Remixed for Vimble 2 gimbal. ... No support or raft required.