Large Spool Holder for Replicator 5th Generation 3d models

Customized version of https://www.thingiverse.com/thing:44906 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=44906

Customized version of https://www.thingiverse.com/thing:44906 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=44906

This brand-neutral phone holder allows you to watch your replicator or take timelapse photos. Attach it to a replicator's corner for optimal viewing. Designed with an iPhone in mind, but suitable for most phones. Use Remote Shutter app (paid) on...

This design is an enlarged version of "DaVinci Filament Spool Holder" created by @ne14pez, modified to accommodate 4" wide (92mm) large spools. I was particularly drawn to the integrated design with wire guide in the original version but it didn't...

I redesigned the Spool Holder created by Allu_500, perfecting its ability to hold large spools. Although not an entirely solid or sturdy solution, this version works seamlessly and prints relatively quickly. Having used this design for over six...

Spole Holder Replicator Master Owner Support Unavailable. Designed for Compatibility with 32 Millimeter Holes and Beyond. Print Settings Options Provided Below. ... Raft Options: Activate/Deactivate Rafts: No Active Rafts Supports Settings: No Supports...

Just a simple spool holder for the large 5 and 15lbs spools. Print two of the sides, uses height flat head #6x0.5" wood screws to assemble. will accept metal bar up to 14mm diameter. I'm using a half inch tube. ...You will need a printer with a bed at...

... application at http://www.thingiverse.com/apps/customizer/run?thing_id=44906. ... Options Used: * Unit Size: Set to one unit * Spool Width: Defined as sixty units in diameter * Hole Diameter of Spool: Established at thirty-three units in diameter

I designed these small, minimal rollers for my large 10kg spools. This design also allows me to use the same rollers with standard 1kg spools. They print as one solid piece with no supports, and use six 608-2RS ball bearings per roller. ... I later...

This filament spool measures 92mm in width and approximately 32mm diameter, which exceeds the standard size for Up! Mini spool holders. As such, I am designing an enlarged holder to accommodate larger spools. Printing at a layer height of 0.2mm is...

I designed a new spool holder for my MMU2, which comes with limited horizontal clearance that doesn't accommodate larger filament spools like 2.5kg. I created this simple holder in the same style as the original but added extra clearance to print...

This is a top-mounted spacious spool carrier designed specifically for the M3D Pro. ...I experienced numerous problems with traditional worktable spool holders, but this one delivers smoothly from above.

This is my attempt to design a larger spool holder to accommodate larger spools. Print instructionsCategory: 3D Printer Accessories Instructions Print on 02.mm layers, fill doesn't really matter as the holder isn't being subject to shocks etc. The...

... by FormFutura. ...As build size expands, so does the need for more plastic in your spools. Simply take out the factory spool holder and attach this one in its place. ...It fits seamlessly into the existing location without any modification required.

There are versions for both the CR-10 type spool holder mount, and a screw mount which can be attached with hammer nuts to an aluminum extrusion. For all versions you will need the "Spool Nut" part and a Spool Holder part. The CR-10 version will...

Versions are available for both the CR-10 type spool holder mount, and a screw mount which can be secured using hammer nuts to an aluminum extrusion. For all versions you will need the "Spool Nut" part and a Spool Holder part. The CR-10 version...

Required Parts Printed parts 2x spool_holder-base.stl 2x spool_holder-inner_bearing.stl 2x spool_holder-outer_bearing.stl 2x spool_holder-spacer.stl Other hardware 2x 5 KG load cell 1x Hx711 control board or equivalent board that can read two load...

The part is designed to hold a plastic tube that guides the filament, specifically tailored for use with the MakerBot Replicator+. ...With an inside diameter of 5 millimeters, it offers versatility by allowing installation on either the left or right...

You can find it on eBay at http://www.ebay.de/itm/IDE-System-HBP-heated-build-platform-for-Makerbot-Replicator-5th-Gen-/352004451045?ssPageName=STRK:MESE:IT. Alternatively, you can also purchase the IDE System from our online store, which is a bit...

Just a simple spool holder for the large 5 and 15lbs spools. Print two of the sides, uses height flat head #6x0.5" wood screws to assemble. will accept metal bar up to 14mm diameter. I'm using a half inch tube. ...You will need a printer with a bed at...

This model have holders for 2 different sizes of large filamentspools: 52mm inner diameter and 105mm inner diameter. - Do You have rolls with another diameter, You can create some holders and change them whenever You feel like it! In the middle of...

... branded filament rolls instead. ...This custom holder and sturdy tube brace enable you to mount the large Makerbot spools directly onto the back of your mini. ...Both components can be printed at once on the mini using the included smaller roll of PLA.

This is a spool holder upgrade for the Robo 3D R1( +Plus) which accommodates larger diameter spools. I initially had several problematic spools for my Solidoodle Press but after acquiring the Robo 3D, I wanted to utilize them effectively. The stock...

This revamped Tinkercad model showcases a modified version of phineasjw's Replicator Bed Level Jig, suited for users with short dial gauges. It marks the creator's initial endeavor in building something using Tinkercad. The variable 8mm diameter dial...

Looking for a way to mount a large filament spool on a Rostock Max? Look no more, print this spool mount and its smooth rolling starts right now. Print the spool roller and bracket, screw the threaded rod into the bracket with ease, slide on the...

Printer Settings Print Brand: MakerBot MakerBot Replicator 2 Rafts: No Supports: No Resolution: 0.4mm Notes: Print 2 pieces upside down without rafts or supports! ...Enjoy printing today!

Max Spool Diameter 30 Centimeters, Max Spool Width 13 Centimeters Print Settings: Printer Brand: Prusa Supports: Irrelevant Resolution: .15 Millimeter Infill: Twenty Percent Notes: Printed with Polylactic Acid (PLA)

This is a robust filament spool holder designed specifically for the Ultimaker 3. Although I have not yet tested it with my own Ultimaker 2, there is a possibility it may also fit that model. ...Once I conduct further testing on the Ultimaker 2, I will...