Large Spool Holder for Replicator 5th Generation 3d models

For standard spools with a central aperture of up to 100 mm that utilize an integrated 608zz bearing, the original design from Sigma3D is specifically tailored for compact center spools. In order to achieve optimal results, users should print two...

A built-in guide within the base of the holder ensures a snug fit for a wide range of spool sizes, making it an ideal solution for various printing needs. ...To minimize material usage and reduce print time, supports are only necessary for the curved...

My Kossel kit had an acrylic spool holder that broke when I caught the power cord on it. So I needed a replacement. I modeled this in SketchUp. For 1kg rolls of filament that are up to 70mm wide. Snaps onto 2020 rail and mounts with an M3x12 screw...

... of mine, making it even larger (width=55mm, thickness=6.15mm). ... Other components on the image are available here: Colorfabb spool holder is located at www.thingiverse.com/thing:205957. ...Fingerwheel is showcased at www.thingiverse.com/thing:3924.

These spool holders securely latch onto and snap over the extrusion frame of the Sunlu S8 printer, providing a stable base that rests directly on the printer's surface. ...To install them, simply print two units and attach them firmly to the frame.

I prefer the TUSH2 design, available at https://www.thingiverse.com/thing:2853619, but discovered the integrated spool holder to be too fragile and constricting when using PLA filament from the Monoprice Voxel. ...It snapped apart three times within...

I built a spool holder that fits snugly inside an enclosure. To secure it, I employed a clever trick using a piece of filament to fill the hinges' holes, then melted and shaped it with a lighter's flame. ...If the filament won't cooperate, you can try...

External Spool Holder attaches directly to the top rear corner of the z18 Printer. The z18 Printer top section sits between the 'Backer Plate' and 'Holder Arm', which utilize ten thirty-second coarse thread screws passing through ventilation slots in...

Hook the lower edge of the frame into the lower opening in the extrusion and then pivot into position (See pictures) Once installed they holders can be slid along the extrusion to fit your spool. Install the spool by placing one rim in the rollers...

These parts were designed to glide over spool holder boxes that measure sixty millimeters deep by sixty millimeters tall. They fit pegboards with a twenty-five millimeter or one inch pitch, and the smaller five millimeter holes. I utilized PETG and...

Wife wanted to organize her spools for her business so i designed these for her metal pegboard Print with the smaller end down make sure you use rafts and supports.

Summary Design revision targets reduced print time and compatibility with smaller spools. ...Optimized settings are as follows: Printer: Prusa I3 Rafts: No Resolution: 200 Infill: Increased to 20 for faster print times.

A friend of mine wanted a system for her thread spools on a IKEA Skadis toolsystem. Designed in Shapr3D and Printed in Prusament PLA with 20% infill and 0.4mm layerhight on a Prusa XL - Single

I'm planning to install my filament spools on the wall to draw inspiration from Martin Majewski's ingenious design, and use it as a model for creating my own custom filament wall mount system.

This is a spool holder designed to adapt to the Anet A8 3D printer. Fixing to the frame is done with the screws of the screen support. The assembly of the uprights requires 4 x M6x25 + nuts. The wire feed plate is only placed, it holds by its weight...

A Simple Spool Holder That Mounts Easily to Any Frame with Just Two M5x10 and T Slot Nuts. Nothing More Needs to Be Said About It. Print Settings: Printer: Hypercube Rafts: Not Required Supports: No Resolution: 0.2mm Infill: 15% Density Notes:...

I found this spool holder and thought that if two holes were removed it could be attached to the 20 x 20 extrusion... and this is what I did. Remix of http://www.thingiverse.com/thing:254796 I printed it in PETG but I'm sure that ABS or PLA would...

This design uses printed parts and four skate bearings to mount a "RepRap"-style spool atop your printer's bars. Designed for minimal material usage, it requires approximately 1.5 meters of 3mm filament. To assemble, print eight bearing.stl files and...

The mainboard fan's intake hole on Makerbot Replicator could use a better positioning, as it is somewhat unfortunate. To prevent small objects from obstructing the fan, a grill should be added for protection. ...Print and glue this grill in place after...

Electric coil winder holds the spool securely in place.

These are adaptors for using large spools of thread on a Singer sewing machine, designed to accommodate tall spools that allow the thread to clear the bobbin when winding. Each size features one version with a bulge and another without, serving a...

The only material used was a standard M8 thread, which I sourced from my scrap box for extra strength. The M8 thread is embedded in the holder, but this might require printing it with a resolution of 0.1 mm. ...Unfortunately, I printed mine at 0.2 mm...

The sides or gables are replicas of the original Anet A8 spool holder, allowing you to simply print the brackets and they should fit the original gables that came with your Anet or equivalent printer, although you might need to file the tabs slightly...

Donations: https://paypal.me/danhil CR-6 SE spool holder replacement with bearings. Fits into any standard 40xx extrusions. Arm.stl is push in joint and Arm2.stl is click joint. Ring.stl needs to be printed twice. I never tested the click joint...

... the last ‘nub’ in.  The desiccant I have from McMaster pretty much stays in, but you don't want to store the spools vertically. The cup sits flush so you can stack the spools.Clear PETG0.2 LayersLow (5%) or even no infill for better vision inside.

... last ‘nub’ in.  The desiccant I have from McMaster pretty much stays in, but you don't want to store the spools vertically. The cup sits flush so you can stack the spools.Clear PETG0.2 LayersLow (5%) or even no infill for better vision inside.

This bracket, designed for a 1/2" rod, is perfect for holding spools of wire or solder. To install it, simply use #6 wood screws and insert them into the pre-cut slots on the front. ...Notably, this design does not require additional support material.

Spacer Bar for Suspend Mount Tube Spacer Insert Between Enclosure & Spool Component Engineered Specifically for Desktop Three Dimensional Printing Device by CTC Inside Opening Measurement is 33 millimeters Dimension Across Thickness Measures 4...

The updated design enhances clamping effectiveness by testing with spools from www.crowdfilament.com and www.leapto3d.com. The revised file "xxx 2.stl" offers improved clamping features. This product is specifically designed for use with a pencil or...

Support base features a vertical post that securely holds a rod, perfect for managing filament spools. A 3/4-inch Oak dowel was chosen as the ideal material for the rod, offering exceptional strength and durability. ...Small countersunk wood screws...