Lavabox DNA200 8mm Extension Rev 2 3d models

Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627

Customized version of https://www.thingiverse.com/thing:44422 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=44422

Customized version of https://www.thingiverse.com/thing:5690103 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5690103

This mechanical coupling holds firm thanks to four strategically placed M3 screws and four accompanying M3 nuts securely in place. ...I haven't tested the print quality yet, but every indication suggests it will perform smoothly as intended.

Customized Version of Conn Director Cornet Mouthpiece: Designed Specifically for a Conn Director Cornet, this Customization Allows for Precise Adjustment of Key Parameters. Created Using the Thingiverse Customizer:...

Customized version of https://www.thingiverse.com/thing:2868900 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2868900

Customized version of https://www.thingiverse.com/thing:2868900 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2868900

Here are the settings I used for the print: Printer: CTC Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Notes: I used PLA, but I don't see why ABS wouldn't work just as well. ...The prints turned out sturdy and strong with these settings and...

... tape; without it, the lock will fly off when the shredder is turned off. To print this design, I recommend the following settings: Printer: Tobeca 2 Rafts: Yes Supports: No Resolution: 200 Infill: 15% I created this model using 3DS Max.

Customized version of https://www.thingiverse.com/thing:2424931 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2424931 Made a Rev 2. ... This one slid too far down the fins and off the end of the tube.

Remix of the Openracer FPV racing drone canopy - for a fixed camera angle (47 degrees) and compatible with only Runcam Racer 2,3 (either 2.1 or 1.8mm lens). Later Runcam Racers (4,5) will not work. Can be printed in Sainsmart TPU (high infill)...

This compartment enables you to carry a fresh Rev Robotics battery and simultaneously integrate a Rev Robotics module directly above the battery.

8mm lebel ammunition

This is an recessed panel mount designed specifically for the [Rev power switch](http://www.revrobotics.com/rev-31-1387/) and comes with an optional shield to safeguard wires if necessary. By recessing the switch, you can prevent damage from...

I designed this extension specifically for the 3DR Solo Smart Drone, allowing it to securely hold my iPad Air 2 and other large tablets of similar size. To install it, simply print and assemble. Please note that you will need to remove a small amount...

Based upon:3018-PROVer [V2] Upgraded Semi Assembled CNC Router Kit3040 Y Axis Extension (3036)https://www.sainsmart.com/collections/new-genmitsu-collection/products/genmitsu-3018-prover-v2-upgraded-semi-assembled-cnc-router-kitTheir...

A mounting device for attaching a servo to a REV platform.

This mount allows you to attach two REV hubs vertically and back to back.

Thumb stud for leatherman rev. ...Slightly larger than the hole, designed to be press-fit.

Just a backup system for a rev counter system or other technical assistance.

BeagleBone Black Rev C for solidworks (2018 and later) and .STEP

... to not break the sides). I wanted to test this design before posting, and have used it in my garage toolbox for over a year now without issue. Also see my three piece set for 1/2 inch extensions here: https://www.thingiverse.com/thing:4721814

This is an case extension for CanaKit Raspberry Pi 4 Aluminum that will fit an Geekworm Raspberry Pi Hdmi-in Module, Hdmi to CSI-2. The is designed require a hole to be cut (Dremel) into the aluminum case to allow the ribbon case to pass through. ... I...

This is a snap on extension for the Perky-Pet YSSF00346-2 Straight-Sided Thistle Seed Wire Mesh Tube Finch Bird Feeder. I wanted to raise the lip on the bottom a bit so that the seed didn’t fall out so easily when the goldfinches flew off. ...

A two-in-one rechargeable robotics battery and toggle switch assembly mounts securely to any robot using an Actobotics-pattern base, providing a convenient housing solution.

Update: I tweaked the Picatinny profile in the carry handle, plus installed a Picatinny rail Punisher cover to complete the job. Using my DualStrusion 2X printer, I just printed out a green and gray Carry Handle. This time around, the Picatinny...