Library Box Case for TP Link MR3040 3d models

Hi, I bought some used TP-Link EAP225 and EAP245 in the new Version V3 and V4 without ceiling mounts. If too sloppy add tape between mount and AP. Use 3mm or 4mm screws. ... Drawn in pretty old Sketchup Make Version 17.2.2555 64-Bits ...

This adapter allows you to rackmount this TP-LINK PoE Switch. It holds both the device and the power adapter. There are no problems with airflow, so the switch doesn't overheat. Simply join the two parts with long screws and it will hold just fine.

Realicé una ligera modificación al soporte publicado en https://www.thingiverse.com/thing:4179052 (gracias dacasma) debido a que la base de la TP-Link Tapo no tiene las mismas dimensiones en el anclaje al soporte. Puede hacerse perfectamente en PLA o...

... switch to it and have the cables a bit more manageable. ... Print in whatever settings you prefer. This was made to fit the tp-link tl-sg108e but might fit others All i did after print is drill small holes to fit the switch to the 3d printed part.

... I simply cut/paste the skadis connector onto the XE75 wallmount. ... ------ TP-Link Deco XE75 mount to attach to an Ikea Skadis peg board. Print base, 2 x 4mm pegs, 2 x 7mm pegs. Glue pegs into base. ... Attach to your Ikea Skadis pegboard.

Boite de jonction design pour camera de surveillance TP-Link Tapo C320WS Nécessite l'utilisation d'une prise femelle compacte Visserie M6x45 (3x), M3x12 (3x) avec écrous et chevilles de 5 ou 6mm (2x) Pour l'étanchéité je conseille des joints de...

I'd like to explore a fresh approach to mounting TP-Link's CPE outdoor routers in front of a window without causing any damage to the walls. To create the base structure, I've built upon my previous project, so please refer to remixlink for the...

This is a wall mount for the TP-Link Deco M9+ Mesh Router and a Netgear GS308 switch. I chose the Netgear GS308 because it uses a 12v PSU the same as the Router so I can use one PSU to power both units. I used the excellent Deco M9+ wall mount by...

This box encapsulate the ST-LINK V2 mini, if you have soldered cables to it on both ends.It is also compatible with a TTL to USB adaptor of the same size.The box have cable retention. ...This is why I made it, instead of just using shrink flex.I have...

This box encapsulate the ST-LINK V2 mini, if you have soldered cables to it on both ends. It is also compatible with a TTL to USB adaptor of the same size. The box have cable retention. This is why I made it, instead of just using shrink flex. ...

I needed to put my TP-LINK TL-SG1005P PoE+ switch onto the wall, but did not find any specific design. So I designed one from scratch. The 4 stud now can hold the switch not too firmly, but fine, sliding into the small gaps. I used PLA as PETG proved...

The compact TL-WR902AC TP-Link travel router finds its perfect home when mounted to a wall, keeping it safely out of reach and reducing clutter. With an ingenious design, this mini router slides effortlessly into place at the top of the mount, making...

This is a new idea of mounting TP-Link's CPE outdoor routers in front of a window, without drilling or damaging the walls. ...As a base i used my last project: https://www.prusaprinters.org/prints/68525-outdoor-windowmountIf you want to build one by...

I needed to put my TP-LINK TL-SG1005P PoE+ switch onto the wall, but did not find any specific design. So I designed one from scratch. The 4 stud now can hold the switch not too firmly, but fine, sliding into the small gaps. I used PLA as PETG proved...

This is a combo 1U mount/bracket that holds both the Tp-Link ER-605 Router and the Netgear Nighthawk CM1200 Modem. Thanks to some handy models by Kazdo and thenixhex311 I was able to whip this up pretty quickly! You will also want 4x M3x15...

Designed to fit theTP-Link Deco AXE5300 Wi-Fi 6E Tri-Band Whole-Home Mesh Wi-Fi System, 3-Pack from COSTCO. Should also fit models sold at the Deco XE75 AXE5400. ...

... bulb and is used rarely. So in my case WiFi router getting too hot is not an issue. PLA will not work as WiFi router gets quite hot even when lamp is not used. PLA will eventually deform. ...PETG is fine.Parametric FreeCAD project file is attached.

these are brackets for a small for factor computer - blank - eSata port - TPLink TG3468 network board tested on an hp sff desktop pc

This is a bracket for attaching a router with mounting holes to a wall. ... The files with model names are already measured for the matching device.

Only had the normal bracket, but needed a slim one for my optiplex.

This design is a remix from the creation of richard64. ...For me, it wasn't obvious how Richard imagined the wire management, so I added some holes. I hope you can excuse me for the poor renders. ...:)

Simple brackets, takes 4 screws. ...Mounts the switch upside down and leaves some air through for cooling. Updated with V2 for a nicer printing result, without the elephant's foot through the rounded bracket. ...It's angled now.

these are brackets for a small for factor computerblankeSata portTPLink TG3468 network boardtested on an hp sff desktop pcYou can find all my models here, thank you who will appreciate with a download or with a like

I added structural strength to the wall mount by editing the wall mount. ... Then I added holes for better cooling performance I hope you like it!

I added two holes to screw it against the wall and I also removed the holes for the rubber feets Printed with:4 Walls20% infill (Grid)

This area remains intentionally empty to enable users to craft their unique assembly configurations, even though it was not originally designed for printing purposes.

Couldn't find suitable a suitable surface mount bracket for my Tplink LS1005G 5-port network switch but the one made by cubiee8995 is close enough as it was designed for the Tplkink SG105 5 port switch. So I downloaded the STL file and reduce its...

5-port Gigabit switch with 4-port PoE+ for use in embedded electronics kits, go-kits, drone video, portable/mobile installations, and just about anything you would like to connect kit. 100x100x25 mm footprint. ... Very compacthttps://a.co/d/fR1ehCg

I revamped my wall mount with cables hanging loose and three holes exposed. ...Lucky for me, there was an unused screw lodged in the wall that I could repurpose instead of making another hole.

these are brackets for a small for factor computerblankeSata portTPLink TG3468 network boardtested on an hp sff desktop pcYou can find all my models here, thank you who will appreciate with a download or with a like