Logitech Keyboard Stand 3d models
257178 3d models found related to Logitech Keyboard Stand.
cults3d
This device improves the convenience of working on a wireless keyboard of the slim line k9 w type and creates a viewing angle that is comfortable for the eyes.
thingiverse
This is a small piece to improve the ergonomics of my ThumbsUp! ...keyboard (https://thumbsup.shop) It raises the board, gives it a bit of a negative tilt, making it more comfortable to type with.
thingiverse
Simple Phone Mount Bracket: Secure Your Device on an Apple Bluetooth Keyboard Mounting your phone for typing has never been easier with this straightforward bracket designed specifically to slide over the round section of an Apple Bluetooth Keyboard....
thingiverse
The keyboard mount has been remixed to accommodate a 13" MacBook Pro, its capacity extended by reinforcing the back brace to support increased weight and rounding off sharp edges for a smoother fit. It now seamlessly integrates with my MacBook and...
cults3d
You can easily overcome the issue of a keyboard being too far away from your screen by printing custom brackets for your Cintiq 27QHD. ...To achieve this, simply load up your Cura software and select the Standard Preset for Polyflex TPU95A, which will...
thingiverse
Check out this pic below - I had a problem uploading something because it was busted. ...I'm rocking an Azio mechanical keyboard right now, but unfortunately, I managed to snap one of its adjustable feet, so I came up with a makeshift solution.
cults3d
Feet for raising and tilting the Arturia Keystep mini MIDI keyboard to best suit your working environment. The version shown in the picture is the version with a slight inclination (6 degrees). 3 other supports with different inclination are...
thingiverse
A replacement part for my Cherry KC 1000 keyboard. Works great, maybe print a tiny bit wider to make the clip-in mechanism a bit more snappy. ... Built in tinkercad, sliced with Cura at 0.12 mmm resolution (should also work with .18 or even .2)
thingiverse
This is for a Kindle 3, the version equipped with a keyboard located at the bottom. I haven't tested it yet, so use it at your own risk. Customized version of https://www.thingiverse.com/thing:512350 Created using Customizer!
thingiverse
If you use a Logitech Ergo K860 Wireless Ergonomic Keyboard and put to much pressure on the 7y degree leg, you can snap it off. This happened to me, so I modeled up a replacement. For FDM I added a little snap off support for the pegs, so it...
cults3d
2 hole for remote : 55mm x 25mm 1 stand for wirelesskeyboard (rapoo e2700) : 8mm
thingiverse
This project started as a phone stand, but kinda got taken over by whatever was in reach at the time. Supports phones, iPads, an xbox controller, snacks, and who knows what else! There are 2 versions. One for the lower stand, and the other for the...
cults3d
Modular Microphone Stand Logitech Rally Mic Pod Logitech Rally Mic Pod Modular Microphone Table Stand
thingiverse
A colleague requested one suitable for the Logitech MK700/MK710 keyboard, and this is the result! Printed with 100% infill, 0.2 mm layer height, and no supports, it was rotated 90° to have a flat honeycomb on the bed. ...It can also function as a desk...
thingiverse
Designed to level-out my all-in-one PC as was sitting approximately 2mm lower one side than the other due to legs bending. ... Also incorporated posts on the front to prop the keyboard up out of the way. ... Included an equal set as well.
thingiverse
I work in an office setting with numerous computer stations and an abundance of keyboards. ...The keyboard stand enables us to optimize our workspace, freeing up valuable counter real estate that was previously occupied by a communal coffee mug.
thingiverse
The Logitech X100 Bluetooth Speaker Stands Tall at 50mm x 50mm x 20mm
thingiverse
[10mm Square pipes] Length , Number 300.000 , 8 , total , 8 A wooden hammer is used for assembly. ... https://denshiman.com/10mm_square_pipe.html <p> <a href="https://ko-fi.com/imaicom"> <img...
thingiverse
This creation was brought to life using Tinkercad's incredible tools. ...You can easily edit and customize it right from their website: https://www.tinkercad.com/things/7QoBrtuOtjz edit online today!
thingiverse
G502 Charging Stand w/ logitech gaming logo Original design of gmartin314
thingiverse
Spare foldable legs instead of broken standart ones (black on photo).
cgtrader
Just a model that i created while i was bored! ...IT also has working RGB.
thingiverse
My enter key was broken in half so I decided to make one :) I used prusaslicer to print it. ...The stl needs to be auto repaired by prusa slicer before slicing.
thingiverse
Mount under desk, chair, on wall, etc., either horizontally or vertically. Print the STL, then snap the piece into two brackets. ... It's arranged this way to maximize bed adhesion when printing.