M14 Rifle with Optical Scope 3d models

A small end-of-filament optical detector, which operates with basic functionality, employs two microtubes of PTFE (preferably Capricorn) along with the most flexible pen spring possible. The more flexible it is, the less it will impede the passage...

The cutout on the slider cap should align against the magball base to position the top post with the optical endstop. ... Once I install my linear rails, I'll post another set of slider caps for the Smart effector and MGN12 block carriages, unless I...

Lens caps to fit my Leupold scope with 43.1 mm OD. Scale this as required to fit your scope, or use the included Fusion 360 file to customize. Prints without supports with main face down on the build plate. There are lugs that fit 2mm bungee if...

... (paralax adjust). ...Inner diameter: 30mm It can be adjusted using a M4 (0.7) bolt with a nut Outside diameter: 120mm Design based on Jim Gaska work... ... Instructions Print in horizontal position

Check out this innovative project on open-e-drums Tumblr: https://open-e-drums.tumblr.com/post/171265375249/optical-hi-hat-controller Key connections: * TIP - 5V * RING - A0 * SLEEVE - GND Code and resources available at:...

Here's the link to my Optical X Endstop: https://www.thingiverse.com/thing:2959995 Update 08/2018: New Adjustable version available! This two-part design requires parts "1-2" and "2-2". Update 2/2018: I fixed the STL Files for the Left/Right...

This set of tool holders, compatible with standard optical benches from Newport or Thor Labs, features two designs to accommodate small screwdrivers and Xcelite Hex Drivers. Mount them on a table using 1" diameter optical posts for the desired...

This is a 6X35mm finder scope based on the following items from surplusshed.com: https://www.surplusshed.com/pages/item/L2075.html https://www.surplusshed.com/pages/item/L14523.html It consists of the following parts: Optical Tube (qty 1) - holds the...

Scope extender for a 47mm scope. This item goes over the scope about 28.5mm and out of it ~50mm. ...(see the picture)

Adjustable optical endstop holder, with the correct orientation of the sensor of the relatively blocking flap. The bracket to the housing is designed to use plywood with a thickness of 6 mm. A separate version for the printer "Good Bot". ... Mounting...

This is an optical adapter designed specifically for use with the DxO ONE camera model. ...Due to the fact that it's not feasible to directly print the metal ring, my design necessitates the attachment of a step-up ring with a diameter of 30.5mm to 37mm...

Printer a detector of end of optical filament for Bondtech BMG extruder, clones or any other extruder with shape for Bowden adapter. Preferably print in dark and as dull color as possible. Requires 2 small pieces of PTFE tube at entry and exit to...

Optical style ceramic chair boasts a vibrant drawing painted directly onto its seat, fully integrated into the overall scene with meticulous attention to materials rendered using V-Ray. ...Crafted in 3ds Max 2009, this model comes complete with...

This mount is specifically designed for a Smartfly Optical Ignition kill, and it's expected to function seamlessly with both regulated and non-regulated versions. It may even be compatible with their Equalizers and regulators. ...To add extra security,...

 3 - Line up both side clamp pieces with the main body and secure with M5 nuts and bolts. 4 - Set scope on top and feed zip ties through the holes. ...Tighten zip ties and feed loose ends back through the holes for a cleaner look. 5 - Mount the scope to...

My son loves using this scope with his massive gun collection! I designed it to fit most firearms, but I noticed that some older models are quite loose. To minimize support material, I print the scope vertically, but unfortunately, some supports are...

... sides. Torch: https://www.amazon.nl/dp/B08XH8YF6J?ref_=pe_28126711_487767311_302_E_DDE_dt_1 Scope: https://www.multitools.nl/richtkijker-gamo-md-3-9x40-ao.html Any scope with a 25,4 diameter tube will do. ... 8x m4 x 12 or 16 mm Bolts 8x m4 Nuts

... It's only fair! Remix of Gruneun's Nerf Picatinny Scope but with 0.2mm clearance so pieces fit together firmly. Crosshairs and scope tube have been combined into a single piece, and sides have been thickened. ... Use M3 screw & nut.

Remix of Nearly Universal Phone Scope Mount v2 [3058823] for Hadley Telescope. Fits phones like Note10+ or 22 Ulltra. All files were printed without support except scope_mount_2Following files were remixed to fit with Telescope -...

For each scope ring, you will need 4# M3 x 25mm bolts and the generic 2 bolts that come with any generic scope rings that holds the scope in place. You will also need 1# M3 x 15mm bolt to keep the ring from falling out. Recommended to be printed...

For each scope ring, you will need four M3 x 25mm bolts and two generic bolts that come with any standard scope rings to secure the scope in place. Additionally, a single M3 x 15mm bolt is required to prevent the ring from falling out. It's...

This holds the optical sensor. ...Insert the optical sensor into this part and the holder inserts into the drop tube. ...Allows for quick change.

mini Photo interrupter / optical switch, model RPI0352E, manufacturer Rohm.datasheet:http://rohmfs.rohm.com/en/products/databook/datasheet/opto/optical_sensor/photointerrupter/rpi-0352e.pdf

... ensures seamless integration with existing systems, enhancing overall performance and efficiency. By leveraging advanced algorithms and machine learning capabilities, this unit delivers unparalleled accuracy and speed in detecting optical signals.

Create a Mind-Bending Optical Illusion Fidget Ball Using Our Seamless MyMiniFactory Integration: Now you can seamlessly import thousands of 3D printable designs directly into the VECTARY tool and export your models to MyMiniFactory with just one...

An optical sensor I recently utilized in a project caught my attention. Please note that I didn't create or design this component, and it remains the intellectual property of its rightful owners. I wanted to share this useful find with the community....

Optical Deception 3D II A mysterious phenomenon manifests itself as an image within a seemingly ordinary picture. The viewer's perception is manipulated by the subtle interplay of light and color, creating an illusion that defies explanation. ...This...

I'm getting a reading from the sensor inside. ...I've got the link to check out. It's over on eBay, where you can find this Finecorsa optical end stop with a printed cable for 3D printing, Prusa, CNC, or Mendel machines.

...... This double-sided masterpiece is designed with a sturdy adhesive that ensures it stays put, creating an eye-popping optical illusion that will leave onlookers mesmerized. ...Share your favorite photos of this frame in action and let the magic begin!

... my DBot to direct drive, I was left with the old extruder part holding the cables. ...this is my attempt to modify it to become a filament runout sensor instead, using an optic sensor, connected to the Raspberry Pi. Category: 3D Printer Parts