MB Epic 280 frame spacers and side guards 3d models

MB Epic 262 and 229 ARM Guards.

These protective Skids shield the bottom plate of your MB Epic Quadcopter, rigorously tested with both versions of the MB Epic 260/280 and the MB Epic Racer 260/280. ...Each Skid weighs approximately 1.5 grams when printed with a medium-density infill...

These Skids Safeguard the Bottom Plate of Your MB Epic Quadcopter, Proven Compatible with MB Epic 260/280 (v1 and v2) and MB Epic Racer 260/280 Models. They Weigh Approximately 1.5 Grams Each, When Printed with 55% Infill Density and Two Shell...

Dual SMA for MB Epic 229, 262, Cinematic 7 - compatible with DJI air unit. Version 2 features increased SMA spacing by 5mm for improved clearance. In Version 3, a dedicated mount is provided for stinger antenna attachment. The original stock DJI...

The concept was born out of frustration with top-mounted battery frames, which often require pilots to land directly on the frame. This can lead to damaged screw heads and chipped carbon fiber components. Additionally, foam blocks used as impact...

The arm guard is specifically tailored for the MB Epic 262/229, serving as the standard accessory included with every purchase. ...This carefully crafted design not only protects the delicate components but also functions as a flexible vibration...

Next, take the provided mounting screws and carefully attach them to the designated screw holes located on both sides of the MB Epic antenna. Once you have attached the screws, proceed to place the VTX antenna into position, making sure it is...

DJI Airunit mount for Multicopter Builders Epic frames

This object was designed and created with Tinkercad. ...Users can edit and modify it right from their web browser by visiting the Tinkercad website at www.tinkercad.com/things/3x4K5QVn1k2.

The wearer of this protective gear can now confidently take a fall without worrying about damage to their epic arm, thanks to the MB Epic 229 arm guard featuring a sturdy landing pad.

Remix of Lucky's Jello Guard to Fit Snugly on the MultiCopter Builder's Exciting New MB Epic Hero Chair

Two side guards for the HSKRC TWE210 frame. One side has a cutout for the usb port of the flight controller. The guards bump out a little for more wires. I printed it with 100% infill and a brim. ...Rotate them so that the cutouts are pointing up.

This is the rear mount for the MB Epic 262 setup, specifically designed to accommodate a diversity receiver and a VTX bulkhead.

You can attach it under the bottom frame of your MB Epic using 20x20 to hold the Caddx Vista with x4 M2 screws. I specifically designed it for the 229, but it should also fit perfectly on the 262. ... To find the Antenna mount with TBS Nano Diversity...

My latest creation is the upgraded MB Epic Chair, specifically designed for the Hero 6/7 model. The sturdy walls in this design provide crucial support during the printing process and can be easily removed once completed, eliminating the need for...

This frame is designed to be printed in PLA with a 0.2mm layer height, and there's no real need to go lower. The frame is incredibly lightweight (approximately 6-7g when printed in PLA). It flies well, but I still need to test its sturdiness. It...

Side guards for the WideWheel electric scooter by Mercane. The four side guards are perfectly compatible with the 2020 model. ... I made these 3D models because the original protections are way too expensive and also to allow the customization of the...

This Hero 5/6 mount fits the MB Epic 262 or 229, but be aware that larger 6-inch props on the 262 may slightly rub against the camera during high-speed operation. The rubbing is minimal and does not affect flight performance, yet it can leave...

I designed and built custom side guards for my Tamiya truck trailer, utilizing a strong adhesive to secure them to the support brackets. ...These sturdy brackets cleverly attach to the Tamiya chassis rails I had acquired to construct the trailer.

I always seem to find myself constantly removing grass from my DRQ250 so I designed these side guards to keep every unwanted item out. They easily clip onto the standoffs. Edit 8.1.2015: I just uploaded a newer version. ...Mainly the same, just...

... that skillfully minimizes camera shake, optimizing image stability for the FPV camera. ...This innovative design enables the user to position the camera at a precise 30-degree angle, perfect for capturing smooth and stable footage with Matty Stuntz.

... protective shield is designed to replace the side panels of your Arrma Talion v3. ...Its design also allows for seamless integration with the Typhon, Kraton, and Outcast models. ... The initial prints shown are from a prototype made using PLA material.

... creating these designs. Adjust your desired thickness using your slicer program. To achieve optimal results, place the model flat on the bed and adjust the Z height accordingly. ...I printed mine at a thickness of 5mm, yielding excellent results.

I simply converted wabmester's svg into an STL for 3D Printing. ... All credit for these goes to wabmester. Adjust your desired thickness using your slicer. (Lay flat on the bed and adjust the Z height. ... I printed mine at 5mm thick)

Epic GPS puck holder for human use.

specialized epic frame cap

I created a custom mount for my GoPro as none were available that would attach on the side. This new design uses standard GoPro mounting equipment. ...Pete Rasterweb initially developed the base idea for this solution.

Attach two cable ties per guard, ensuring a snug fit to the frame. After four hours of riding, these supports remain in pristine condition, indicating they can withstand the demands of time. ...They were crafted from high-quality PLA material and...

I've also included a less rockerd spacers for a .75mm rocker and the original spacer rocker. Be sure to print the model that you want or print all of them and play around with your rockering setup. ... I've skated these with standard PLA for a few...

I've also included a less rockerd spacers for a .75mm rocker and the original spacer rocker. Be sure to print the model that you want or print all of them and play around with your rockering setup. ...I've skated these with standard PLA for a few...