Makerbot Replicator 2 E3D V6 lite mount 3d models

Simpler mount, but it does require a couple holes to be drilled into the plate and threaded for M3 screws. Overall, it saved on weight by quite a bit and made things look a bit more visually cohesive. Honeycomb design for a bit of flair. You *will*...

I needed a way to support cables coming to hot end so I modified existing part with some cable holders. ... Update 1/1/21 version 2 added - stronger arms and main cable hold moved a bit to back to make more space blTouch probe

This Remix of the original did not have any Fan mounting so also was not good to be used. My remix is make and can be used with my setup and can go up all the way to 320mm. Yes you will loose around 10mm in X-Axix and Y-Axis. but if your glass...

This Remix of the original did not have any Fan mounting so also was not good to be used. My remix is make and can be used with my setup and can go up all the way to 320mm. Yes you will loose around 10mm in X-Axix and Y-Axis. but if your glass plate...

I appreciate the original fan mount by invent0r for the 12mm inductive sensor, but I found that it lacks essential support for the top of the sensor. ...This might be sufficient in some scenarios, but the sensor can become tilted due to the wires and...

However, it falls short in one crucial aspect - a suitable mount for a 40mm cooler is nowhere to be found. My revised version addresses this issue by incorporating a screw that keeps everything stable even at high speeds. Alternatively, the pin-based...

I designed a front-facing rectangular mount that securely sandwiches the hotend onto its original base. Four precision-crafted holes are included for four M3 25mm screws, fastened with M3 nuts that ensure an ultra-tight fit when screwed into place.

After printing out the original design, I discovered a discrepancy in the mounting point spacing. To accommodate this, I remixed the dimensions to match the standard Tech2c hypercube x carriage. This revised remix is currently limited to the 12mm...

This simple pressure-fit mount is designed for e3dv6 on tronxy/cr-10 machines. It has space to fit part cooling fans from here: https://www.thingiverse.com/thing:540716. Use washers to secure the part cooling arm to this attachment. When installing...

I purchased this fan through Amazon here: http://www.amazon.com/gp/product/B00E4AAJ9O?psc=1&redirect=true&ref_=oh_aui_detailpage_o09_s01 It's held onto the carriage using standard Wade Extruder fan mounting holes, which makes everything easy. Just...

Human: The rear carriage of Frankenstein's monster is known as 2_carriage. Unfortunately, it will not function properly on the original Anet frame. This particular component was specifically designed for a specific frame found at...

### Ramps & E3D variant for Adoptabot ---------------------------------------- [Bobblejot Website](http://bobblejot.com) [Bobblejot GitHub](https://github.com/Bobblejot/) [Bobblejot Twitter](https://twitter.com/bobblejot)...

The hotend nozzle is going to be couple of centimeters off in both the X and Y axis. The fan duct is going to collide with the horizontal 2020 extrusion - you are going to need to use the visible hotend modification to avoid collision (and further...

design for GRL FPV PRO 2 Fits a GoPro Lite (TAGE Edition) which can be built from here: https://www.thingiverse.com/thing:5022882 54g GoPro 5,6,7 Print in TPU at 35-40% infill. Less is more. ... Frame:...

The segment that is mounted onto the original ormerod holder should be printed on its back. After having spent too much time editing feature trees in solidworks i have given up adjusting the shape of the air duct and resorted to sand .5mm off the tip...

Hotend Model E3D V6

E3D V6 Nozzle assembly.

E3D V6 Nozzle assembly.

The original mount was reworked to accommodate two distinct hotends - one E3D v6 (left) and one E3D Volcano (right). As Volcano is significantly longer at 8.5 mm compared to v6, the mount groove for the v6 was reduced by 8.5 mm compared to original...

1 : https://www.thingiverse.com/thing:5030130 Moved fan mount more vertical, in order to get it closer to effector and hot end axis. V1 interfered on my printer with timing belt (on A tower) on it's extreme range. V2 fixed that issue. ... This needs...

1 : https://www.thingiverse.com/thing:5030130 Moved fan mount more vertical, in order to get it closer to effector and hot end axis. V1 interfered on my printer with timing belt (on A tower) on it's extreme range. V2 fixed that issue. ... This needs...

The sections where fans are mounted should be printed with that contacting face facing towards the build plate. The component that is attached onto the original ormerod holder should be printed on its backside. ... After spending an excessive amount of...

--- Changelog --- V2.0 (enhancement): - Increased clearance for 40mm fan V1.3 (fix): - Added holes for 40mm fan installation V1.2: - Rounded edges on link component - Smoothed out nozzle duct part - Optimized body design for Creality CR10 with...

This upgraded version 2 is significantly more streamlined, allowing for seamless installation and effortless removal of the hot end in case of any problems.\r\n\r\nDuring printing, position the model so that the base rests on the bed, while the...

... conjunction with Makerbot's E3D Hotend Swap upgrade kit. ...This setup provides a comprehensive solution that includes designs tailored for both single and dual extruder configurations, specifically catering to the needs of Replicator 2 and 2X users.

A custom upgrade kit for Ender-2 and CR-10 printers brings superior cooling to the table with a 30mm coldend fan and two high-performance 5015 blowers. This results in exceptional parts cooling, making it easier than ever to manage wire harnesses. A...

I've been upgrading my Da Vinci 2.0a, trying out various modifications and facing numerous problems along the way, prompting me to design some parts from scratch. The drop-in component is being repurposed; it needs holes drilled into it to attach...

... center plate with back side facing downwards to the table, also using support for the overhang area. Funnels: Drill holes for fans 2.5mm in diameter and use 3mm screws. ...I printed my items in ABS, thereby preventing melting due to a very hot bed.

I had to break up the entire mount because it wouldn't fit all at once on my handheld device.

Remix of 2 parts in the https://www.thingiverse.com/thing:4329200 to allow it to mount a Bondtech LGX lite extruder.Need to change the lower M3 screw of the Bondtech LGX lite with a longer 30mm one.Also uses a M3 screw instead of a M2 on the...