New Clamp for IKEA Jansjo LED Light 3d models

New Round LED Pendant Light Modern E27 LED Pendant Lamp Coffee Bar Pendant Lamps Nordic Iron Lampshade Pendant Light

Clamp for a 90 degree LED profile that is used to mount LED-s in corners. ...This clamp turns a corner profile into a standard one so it can be used in other displays.

Add-on Solution for Enhanced IKEA LED-Chains - A Replacement Star Covering Original LEDs.

I made this model because I couldn't find andy clamp style mounts for my C200 IP Cam, in the hope that it wouldn't wobble as much as a top/wall mount. The only things I could find were wallmounts or smaller clamps for the c100, so I tried to do my...

Shoji-style lamp pairs perfectly with a warm glow of an LED candle or the soft ambiance of an IKEA Puck light.

I prefer using the Jansjö Lamp from IKEA for my Anet A8 printer, but it kept getting in the way. So I designed new frame parts with two holes to attach the lamp directly to the frame. Now it's a breeze to have light on my printer wherever I want.

I crafted this custom housing since I wanted to draw attention to my printer and the Ikea Jansjo USB version caught my eye with its sleek design. To ensure a snug fit, I designed the housing deep enough to accommodate the actual plastic part of the...

A clamp to stabilize the wooden railway parts above groundThe set we bought already had some, but not enough ;) As the wooden railway parts have quite a big tolerance, the clamps can be tight or a bit loose, but It'll work anyway. ...Printed about ten...

A clamp to stabilize the wooden railway parts above ground The set we bought already had some, but not enough ;) As the wooden railway parts have quite a big tolerance, the clamps can be tight or a bit loose, but It'll work anyway. ...Printed about ten...

For this build, you need the following parts from IKEA: - 2x SKYDRAG 60cm LED -> https://bit.ly/2JwiybA - 1x TRÅDFRI Driver 10w -> https://bit.ly/37rRHpk - 1x FÖRNIMMA Power Supply Cord -> https://bit.ly/3ocC8c8 IMPORTANT: You need to change the top...

The IKEA Article Number for this RGB LED Light Set is 401.923.61. Instructions for Mounting: First, carefully push the thin flange of the clip into the positioning hole in the Vertex frame until it reaches the corner securely. ...Next, insert the LED...

The new version of the Ikea SOLVINDEN lampshades don't fit perfectly, they must be adapted and cost more than what I paid for the LEDs :) So I designed these little lampshades, I hope you like them. My only request is: don't reuse my lampshade for...

It's a new version of: https://www.thingiverse.com/thing:3002769 The IKEA JANSJÖ bedside lamp is very practical but its light spot is extremely strong and can't be adjusted by dimmer or bulb change. I created a small attenuator that is fixed on the...

This is a remix for original "https://www.thingiverse.com/thing:2610927" by https://www.thingiverse.com/3D_PP but with easy to remove support (snap it off with pliers) Printing: layer heighth 0.2 infill 50% supports: NO SUPPORTS

Ronkeli's ingenious design was a starting point that inspired me to refine the clamp, adjusting it to provide a secure grasp on the Ikea warm white LEDs, which happen to be ever so slightly larger than average. ...Big shoutouts to Ronkeli for pioneering...

Remix of: Prusa I3 MK2 Frame Holder Collection: 1 Filament Guide by wschadow https://www.thingiverse.com/thing:2053500 and Ikea LED holder set for Original Prusa i3 mk2/mk3 by HenriDIY https://www.thingiverse.com/thing:2419702 Check out my video:...

This is a remix from https://www.thingiverse.com/thing:4739055 Print Settings Printer Brand: Anet Printer: A8 Rafts: Yes Supports: Yes Resolution: 0.2 Infill: 60% Filament: c-tech PLA light grey Notes: My printer: Anet A8 Plus Print the bolt...

This is a simple MK3 mount for the LED NORRFLY from IKEA , this uses 24V so it can be powered from the MK3 power supply. ...This lights up the build plate so I dont need to have the room lights on for the web camera. Print in PETG or PLA with normal...

Cap for an LED to create great Decoration for the table at new years eve.

I needed to adapt an IKEA 24v LED light to my bathroom vanity that housed 53mm incandescente lights. I drew this up using Fusion 3670 (My first design using this program). ... This is version 3 that reduced the material needed and tweaked a couple of...

I use the IKEA JANSJÖ bedside lamp which is very practical but its light spot is too strong and cannot be adjusted by dimmer or bulb change. I made a small attenuator that is fixed on the head of the lamp, allowing for softer and more diffuse...

Igor's articulating LED lamp is one of the most popular 3D printable thing. I really like it. It's easy to install and good adjustable lamp to my 3D printer. I thought it would be nice to attach it directly to the x rail. I did not found such a part,...

... Alu towers with the mounting holes on the LED strip and secure it in place with a firm press or a screw - make sure they're snug, but not too tight! Finally, plug that baby in and enjoy your radiant new light display shining bright like a diamond.

In my case was better to join the LED light holder and the filament guide in one piece. Remix of: Prusa I3 MK2 Frame Holder Collection: 1 Filament Guide by wschadow https://www.thingiverse.com/thing:2053500 and Ikea LED holder set for Original Prusa...

This design is specifically created to work seamlessly with the Ikea Ledberg LED light strip and ensures it securely attaches to the top rail of an Ender 3 / Ender 3 Pro. It also includes a mount for the light switch and cable covers, which help...

Attach the Dioder LED Strip Holder securely to the X-Carriage of your IKEA 3D Printer for seamless illumination during printing operations.

... else, even at IKEA. It was designed for printing on the side of the exhaust pipe with support from the build plate only (for the connector pins). ...This allows you to achieve maximum strength in the pins while minimizing cleaning afterwards.

This tiny addition slips seamlessly onto the IKEA JANSJÖ lamp's end, taming its intense light to allow for direct gaze without risking scorched retinas. Print with more opaque material for an even greater dimming effect. Sized precisely to fit snugly...

... While the Dioder and Ledberg differ in price and separability, a hack is available at http://www.ikeahackers.net/2011/11/how-to-ledberg-lighting-wiring-hack.html, along with new connectors on Thingiverse at http://www.thingiverse.com/thing:121247.

I'm planning to link IKEA Ledberg LED strip to IKEA Deltorf, so I designed this straightforward clip to secure the led onto the metal framework.\r\n\r\nIt works perfectly!\r\n\r\nYou'll require about 4 or 5 for each side if you want to cover the...