Obstacle Course 3d models

I wanted something easy to move/transport, easy to customize (future-proof, who knows?), and, of course, something that looks nice to see. In the starting project, the idea was to reuse all the electronic parts of the OEM machine. However, due to...

But it could also be my own feeling getting in the way since I'm freely moving a 17HS8401, 1.8-degree, 48mm stepper motor as well, and of course, two bearings and both gears. -Filament Loading Issues A flat End-Piece of filament won't get in that...

Of course you can purchase new ones as well, you will need 4x LM10UU. I was not able to remove the brass nut, so I purchased a new T8-4 rod 40mm, and another set of these backlash free nuts.</p> <p>Mount the LM10UU in the ZAxis. Install the backlash...

(Easy, cheap and fast to order directly from Asia). Soldering iron and rudimentary electronics knowledge required. Wetterkappe: https://www.thingiverse.com/thing:3559140 Weather cap: https://www.thingiverse.com/thing:3559140 Eine eigene Kappe werde...

The carbon fiber "dulls" the print and of course ABS can handle the heat well. A lens this wide is for outdoor use. If for some reason you took a photo of someone with this lens, they will run for cover if they ever saw you with a camera again! I...

You don't have to, of course. It's just softer than PLA or PETG. I use two perimeters and only 5% gyroid infill to make it as soft as possible. I have tried using variable layer heights to smooth out the edges, but that does make it a little...

The advantage of this construction is that the LEDs can of course be combined as desired. If you don't need the ultra-bright ones, just take strips with fewer LEDs. And the length can also be flexibly adjusted. The aluminum profiles are available...

À savoir : À force de manipulation les lames peuvent se "froisser" et perdre leur aspect lisse, les frotter en force avec un manche de tournevis ou autre en plastique dur peut netement en améliorer l'aspect EN Translated with...

(And yes, of course I know that this is not how the z-axis support must be mounted, I did this just for illustration purposes.)Print instructionsPrint the t-nut on the side to significantly improve it's strenght. If you print it upright, you will put...

Since I designed most of the interior as open, the biggest benefit was not wasting unneeded plastic to fill in these areas. To finish it off, I of course found lots of great accessories here on Thingiverse such as: The spool holder -...

They have a pseudo "seal" that reaches about 1mm into the tube on both ends, which is supposed to better keep lint out of them. But of course, at the end of the day, these are simply tube-shaped closeable containers - you can put anything in them....

Where my Fan Duct is great: - Cools the hot filaments quite well - Height-adjustable - Can be mounted with the DC42 IR Sensor (I can highly recommend it, but ignore the mounting points if you don't have one) - Because it just mounts directly to the...

Of course, by this time, no vendor had it in stock. I ordered a cheap normal hair clipper instead. This turned out to be a good thing because I later learned that the flowbee will only cut 1/2" on the shortest setting, and I need 12mm and 3mm...

When put in a Slicer and with a decrease of the scaled height by 5 cm (≈ 2 in), the results are still of good quality.&nbsp;The tBulb edition is split into parts and reaches, when put together, a height of 28,5 cm (≈ 12,96 in).&nbsp;Both versions are...

Siehe --&gt; https://www.thingiverse.com/thing:3811614 ENGLISH: For the MK3/s for Prusa I have equipped the Z-slides with a belt tensioner and a clamping function for the liners. This project is based on "Revised X-Axis (Prusa I3) by vekoj" but is...

... one can not be removed like your used to. just install it. and then use a HEX key or a metal pin or long M3 bolt to lock every thing into place. and of course 1 spring and 1 pins is needed to make the mag catch work. Category: Sport & Outdoors

I was tired of guessing how much beer was left in the kegs in my keezer (so I could plan our next brew day, of course). So, I whipped up this simple keg monitoring system to run off of an Arduino. I even programmed my Arduino to run on two kegs and...

You'll find it easiest if you slide one nut into place, squeeze the bearing mount slightly to hold the nut still, then slip the Allen wrench through the screw hole, and then squeeze the bearing mount together as far as it will go, to set the nut into...

Though there are many available setups, I of course have not designed them all and I am willing to take requests and modify sections to fit those needed changes. I only require a link to the part, with dimension for mounting.\r\n\r\n***(I HAVE NOT...

Of course, you can save yourself the effort if you can use M3.5 or M3 screws, which should go through the existing holes without messing with the existing - partial - thread. Print Settings: Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2...

The springs on the underside of the cover have their own removable supports, but you can of course tell your slicer to print them with soluble material if you have the hardware for it. Although I designed the top cover receiver slots with adequate...

... spools available, and here is another one. This fit my needs, maybe it will fit yours as well. I included the step files if you want to modify anything. And of course, just let me know if there is anything I can change to improve this for you.

This doesn't necessarily need painted but extra bonus if it is.Print settings: I would recommend the hollow version with hole: -No supports, no infill, 3 perimeters, .3 layer height (or less is better of course),&nbsp;If you have a bigger Nozzle The...

Visit Buy Webdad a coffee Are you worried your dinos will rampage through the box eating all the patrons while it is on the shelf (of course they can have all the hooligans they want, but patrons, come on!)? Worry no more - with this set of trays and...

And of course, adding your own graphic should be relatively painless as well (see instructions below).Note: The STL and 3MF files included here are set up for multi-material printing. If you want to do a single-color print, you can just print the...

I don't really need the IR functionality, but I had the camera available, so I used it. Links: How to use the mounting plate to attach the articulated arm to a printed frame (in this case carrying a C270 webcam)...

Take your time. Last but not least You only need to switch on the battery in stand-alone mode of it's main purpose. If you want to use it on your computer, the switch can stay off. Charging, of course, only works when switch is on. ;-)</p> <p>How did...

Games with Labo-VR support (besides Labo itself, of course) include "Mario Odyssey," "Zelda," "Captain Toad - Treasure Tracker." There are also some third-party games supporting this, such as "Spice and Wolf VR" and "Thumper." I used the "VR Box"...

Even though the enclosure was far from being air-tight, other than the port, of course, it sounded great. It's never going to be as good as a sub with a larger driver in tonal quality or volume level, but given its 3" size, it's amazing. I'll be...

Of course you need a power outlet at the spot, where you want to install the lamp. Drill two holes for dowels (if required) at a horizontal distance of approximately 6 cm (there is a 5 mm tolerance for both the distance and the horizontal line). The...