Pin Headers for OpenSCAD 3d models

HX711 Strain Gauge Amplifier Module with round pin/socket headers. ...Draw in FreeCAD with "Reasonable" detail.

Straight & 90° Angle2.54 mm pitch1-40 pinsDouble Row Male Pin 1-40 pinsTriple Row Male Pin 1-40 pins

Female pitch headers feature a 2.54mm height isolation and contact at 3.2mm.

Female Pitch Headers Attach at a 90-Degree AnglePitch Distance: 2.54 MillimetersInstallation Locations: Rows 1 through 40, Positions 1 to 2

Instructions Using the Following Options: x Offset from Edge: Set to 2 Units Number of Pins: Specified as 12 Pieces Rows: Configured for a 2-Row Layout z Offset from Edge: Adjusted to 0.5 Units Row Distance: Measured at 15.24 Units Pin Offset: Set...

Customized Version of Thingiverse Design: http://www.thingiverse.com/thing:1381358 Created with Customizer: http://www.thingiverse.com/apps/customizer/run?thing_id=1381358 Instructions: Using the Following Settings: Row Distance Set to 15.25 Units Z...

... Pin offset is perfectly set to 2.54 units. Number of pins required is accurately set at 12. Rows = 2 Row Distance = 15.24 mm Z Offset From Edge = 0.5 mm Y Offset From Edge = 1.8 mm X Offset From Edge = 2 mm Pin Offset = 2.54 mm Number Of Pins = 12

Customized version of https://www.thingiverse.com/thing:3730174 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3730174

Customized version of https://www.thingiverse.com/thing:3730174 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3730174

This case is designed to contain the T-Display with female headers soldered on, so that the entire module can be plugged onto a base unit with male headers, allowing the T-Display controller to be easily removed for reprogramming or used on a...

... headers and Amtek Technology IDC1 series sockets, it can also work with various other options. To use the adaptor, optionally remove the header, apply glue to its sides, and reattach the adapter, resulting in a snug fit and enhanced performance.

Remixed it to achieve an increased vertical dimension at the top when attaching the RedBear to the Pi Zero via headers. ... The original design can be found here: https://www.thingiverse.com/thing:2137152

Probably I should have changed the location a little of the cutout for the screen and/or shrunk it up, but it works ok for now. Maybe I'll remix it one more time to put the indent for the temp sensor. EDIT: Added a second one with smaller...

The inner and outer tubes have pressed-fit, featuring weld holes for enhanced part connection. ...The outer flange can either be welded on or manufactured alongside the outer tube.

Customized version of https://www.thingiverse.com/thing:3730174 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3730174

【Pin Header Guard for Arduino Shield】 Arduino各種シールドのピンヘッダーをガードするためのブラケットです。 Arduinoのシールドはピンヘッダーがむき出しになっているので、テーブルを傷つけたり保管する際に曲がったりする場合があります。 ブラケットを取り付け、それらをガードします。 30分ほどで出力でき、そしてとても便利なアイテムです。     【Google Translation】 A bracket for guarding...

Made it specifically to address her need for a power bus on RC type connectors, and discovered that a dual header strip works great when all pins are soldered together in one neat spot. The problem was mounting this on the mouse itself, so I...

A microarray quill pin holder, designed for use with positioning robots, ensures efficient microarraying. It's part of Dr.RobotLabs OpenScad Library. For a demonstration of its printing process, check out this video:...

MP1584EN DC-DC adjustable buck converter with round pin/socket headers. ...Drawn in FreeCAD with "Reasonable" detail.

MP1584EN DC-DC adjustable buck converter with round pin/socket headers. ...Drawn in FreeCAD with "Reasonable" detail.

I needed to make an adapter for a 6-pin inline to 6-pin in two lines connector... Category: Electronics

SummarySince the pins used in the original design are only available from big distributors (DigiKey, Mouser, ...) Shipping costs 20€. Stackable Pin Headers can be found much more often and are therefore more affordable.Additional Parts needed...

I had to create an adapter that would convert a 6-pin inline cable into a standard 6-pin in two-line connector setup, requiring minimal modification and maximum efficiency.

To ensure that the newly printed pin was robust enough, I creatively engineered it to be constructed sideways instead of straight up. ...Consequently, I needed to craft two individual parts that would eventually be attached using adhesive, but the end...

... It's used in a chessboard project, where the plate connector holds multiple prints of the pin_layer together and adds spacing at the bottom for cables. To customize your print, use the SCAD variables to display only the parts you want to print.

This is Headers Remix for the LS3 Chevy Engine (https://www.thingiverse.com/thing:1911808). The features include: . Replacing fake screws with holes for real screws . Gaskets . Exhaust collector for driver and passenger sides My finished...

http://thingiverse.com/apps/customizer/run?thing_id=1381358 Instructions Using the following settings: Number of Pins Set to 15 Rows Configured at 2 Row Distance Established at 15.24 mm Y Offset from Edge Calculated at 1.8 mm Pin Offset Determined at...

A case designed for the Saint Smart Uno featuring GVS headers has been created using Tinkercad software. ...To edit this model online, visit https://tinkercad.com/things/fpAzS3rtfR2

... Rails for 2,6 mm busses and Dupont headers in my DIY Power Modules to be used with fischertechnik. ...They facilitate Dupont headers and the PTN2-10 cable shoes.For more information see https://www.whizzbizz.com/en/pcb-terminals-for-fischertechnik

I use these Connector Rails for 2,6 mm busses and Dupont headers in my DIY Power Modules to be used with fischertechnik. They facilitate Dupont headers and the PTN2-10 cable shoes. ... For more information see...