Revised Simple Mount for G1W Dashcam 3d models

This accessory works seamlessly with the Apeman C660 Dashcam, serving as an excellent substitute for the original lever on the suction cup mount. ...The central hole is remarkably secure, preventing accidental detachment at all times.

This can be used with the Apeman C660 Dashcam as a replacement for the lever of the sucker cup mount. ...The hole in the middle is pretty tight so it wont fall off Category: Automotive

Combination radar detector and blackvue camera mount for 981 Cayman. May work with other Porsche models. For Dashcam only can be used as is. If using radar detector mount, you will need to buy an existing radar detector to steal the mounting...

This is a rearview mirror mount for a Cobra 840 Dashcam. The suction cup one fails regularly in the summer, and repeated falls are damaging the power jack, so I came up with this. The stem is in two pieces to accommodate angled rearview mounts, and...

A device designed to securely fasten onto a Tesla Model S's interior rearview mirror stem, creating a sturdy base for mounting a dashcam. Alternatively, it can be utilized for radar detectors as well. The unit features a straightforward camera...

This is a ball mount for Garmin Dashcams that will allow for the use of 3M adhesive to secure the camera to the bottom of a rear-view mirror cluster or similar. There are 2 pieces. one is shorter than the other. This is my first creation and...

Adapter brackets for fitting a Blueskysea DV128 Dashcam to a 2019 Honda CB500X.

The mount is made for connecting my discontinued Apeman dashcam to these [ball join mounts](https://smile.amazon.com/gp/product/B074GXM5W4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1). It's my first ever 3d model, so there's plenty of room for...

This adapter enables the Yi Dashcam to seamlessly integrate with widely available GoPro-style mounting hardware. ...The camera securely resides within the frame thanks to a 1mm lip along the screen side and four corner clips positioned at the front of...

This fits most Thinkware dashcams according to my knowledge, I used it with an FA200. The tolerances on my printer/filament aren't that great for interlocking parts. You'll likely want to scale this down around 2-3% if your printer is...

This design might also work well for printer camera mounts, depending on your specific needs. The holes are pre-drilled with M4 hardware in mind, but I used M3 screws because I was running low on M4 screws. To secure the camera in place, use...

Simple and light support for the 70mai A400 model.Attaches easily with double-sided tape.The camera is mounted and dismounted through slicing.Adjust clearance in the CAD file (stl file). ...PS I found 0.1mm radius best (loaded version).

The pad is 40mm square. Print Settings Rafts: No Supports: Yes Resolution: .2 Infill: 60% Notes: You might need to adjust the orientation of the mount on your printer for the best support of the arm. It can be done without support, but looks better...

Mount for 70mai pro plus. support required. ... Use layer height 0.1mm for better quality

It's a dashboard cam mount for a rad power bike they have a standard mount point on the front of the frame

This is a rear camera mount for a Honda Element. ... It attaches to the cargo hook using a J-bolt.

A basic circular mount is designed specifically to hold a 70mai dash cam securely in place.

This is a GoPro mount for my 2019 Mazda Miata ND GT and also works for my Hyundai Kona. The circular clamp dimensions should fit exactly the rearview mirror with autodimming and homelink. It is angled to avoid the power connector behind the mirror. ...

I designed this mount, bcs the original is broke and also, I wanted to be able to remove the camera.

I crafted a custom mount from scratch since the original was defective, and I also needed to ensure that the camera could be easily detached.

This is a GoPro mount for my 2019 Mazda Miata ND GT and also works for my Hyundai Kona. The circular clamp dimensions should fit exactly the rearview mirror with autodimming and homelink. It is angled to avoid the power connector behind the mirror....

I needed a custom spot for my 2016 model Elinz dashcam to fit snugly in my Land Rover Defender. To solve this, I designed a mount that fits into the same sun visor mounting hole on the passenger side of the vehicle. This mount uses the exact same...

... mm. If you need to mount the G1WH dashcam on a 2015 Subaru Forester, print components "Forester mirror clamp bottom" and "Forester mirror clamp top" instead of "mirror mount clamp" and "mirror mount main". ... The assembly video is available here.

I printed this to mount my TOGUARD dual dashcam onto the rear view mirror of my Subaru Outback with eyesight, if you have similar requirement this may be useful to you too. hope this help. Drive safely and GOD bless. ...

To use the dashcam mount the Mini Dashcam has to be modified by removing the GPS mount bracket. The GPS is to be mounted at a separate locate on its own mount with 3M tape. ... Link to dashcam:...

I popped open a GS8000L dashcam and managed to misplace one of the micro tactile buttons controlling the power switch. I replicated this by meticulously measuring the sole remaining button, which turned out to be a brilliant solution after some minor...

Create an Arduino Uno holder for Glasswalkers Revised Fully Printable Eggbot mount, v0.2.5. Enhancements include improved hole positioning and a sleeker design. Print the STL file to receive the mount and four spacers. ...Assemble by attaching the mount...

a motorcycle handlebar mount for a Vsys motorcycle dashcam operation button the ring part should be printed from TPU or other flexibles all other parts should be printed from UV resistant material the Dashcam mount would be published later

... the models have the female threads modeled in the stl and don't print well with a 0.6mm nozzle. ... So I revised the M5 threads to be a plain bore at the normal tap drill size so you simply need to run an M5 tap through the hole to cut the threads.

This is a remix of [the original mount](thing:3097540) created by Kraegar and Roy Sun.\r\n\r\nIt boosts the stepper mounting holes by 2mm, allowing a full-sized stepper to clear a button head screw. ...The original design demanded use of a countersunk...