Shimano TL FC32 Installation Tool 3d models

A time-saving alternative to the Shimano TL-FC32 Installation Tool, made possible by including the TL-FC25 Adapter, which comes with compatible Shimano BSA bottom brackets. By minimizing the need for purchasing frequently used bike tools, one can...

Shimano TL-8S20/TL-AF20 Right Hand Cone Installation Tool for Alfine/Nexus/Inter-8 internal gear hub. This is the counterpart to https://www.thingiverse.com/thing:5646832 which is used to remove the cone. ... The window has been added to be able to see...

This is a Shimano Tool (TL-FH16) to Install the outer seal Ring (Y3FM26000). ...For use with Shimano microspline freehub FH-M8110-BS, to set the correct deep.

SHIMANO TL-EW02 DI2 TOOL FOR E-TUBE CABLE

The Shimano TL-PD40 pedal tool requires the use of a 22mm socket wrench for operation.

Shimano Crank Installation Tool Specifically Designed for Hollowtech II Systems

This is a Shimano crank installation tool designed specifically for use with Hollowtech II systems.

Revised Design: Compact TL-FC32 Version This updated design shrinks the original TL-FC32 for compatibility with the BB-MT800 and other compact Hollowtech II bottom brackets. It was printed using 7 shells and a 50% infill, resulting in an effective...

This tool enables you to fine-tune the Bottom Bracket's axial clamping force for Shimano Hollowtech II cranksets, ensuring optimal performance and durability.

This tool is designed for efficiently tightening (or dismantling) Shimano pedals such as the PD-540 SL and PD-5600 SL models.

... making Tool2 sufficient for the task at hand. Tool3 can be printed without any support structures. Choose the tool that suits you best to tighten the crank arm, ensuring it has no play yet not so tight that it presses hard on the bearings.

The tiny cap this tool loosens and tightens requires a precise torque of 6-8Nm to move the left crank close enough to the bottom bracket bearings without pinching them. To comply with Shimano specs, I first tightened the cap to its specified torque,...

This device enables fine-tuning of the non-drive side crank arm's bottom bracket bolt on Shimano Hollowtech II cranksets. ...Losing mine means I can print new ones via 3D technology whenever necessary.

I installed a 1/4 inch square hole in the back of the tool, allowing for easy use with a ratchet and providing added leverage when removing a stuck pre-tensioning cap. ...Tightening the cap, however, requires minimal effort since it only needs a gentle...

This tool can be used to loosen that Torx-like cap, which is holding the left crankarm on the bottom bracket spindle (see picture). This is needed to swap/clean your crankset or replace the chainrings. The video here explains how to remove your...

Use this tool to unscrew the Torx-like cap on your left crankarm, attached to the bottom bracket spindle (as shown in the image). This action is necessary for swapping or cleaning your crankset or replacing chainrings. View a video demonstrating...

Stronger design with higher wall thickness throughout and reinforcements at the relevant points. ...Fits perfect on my Shimano Steps Lock Ring (Y78N00085, Drive Unit DU-E6100). ...

Shimano offers the TL-PD40 for this specific task, but I lack a large enough wrench or the suitable Bottom Bracket tool to operate it effectively. Therefore, I created an alternative version that fits my existing Park Tool BBT-9 for my Hollowtech II...

This high-quality crankset features Shimano's renowned Hollowtech technology, providing an exceptional balance of strength and lightweight design. Whether you're tackling tough climbs or sprinting across the finish line, the TL-FC16 is designed to...

Shimano pedal service tool TL-PD40-BTL-27L a tool to disassemble the shimano pedal. Similar to the TL-PD40 tool. can be used in combination with a 44 mm bottom bracket tool. ...I use it together with the BBB/BTL-27L.

This tool is designed for easy removal of cassette gears using a Shimano TL-LR15 tool. Travelers on bikes will find it particularly useful. ... A stronger Version 2 model exists, yet neither is fragile.

This is similar to Shimano's TL-AF10 tool. The tool is a snug fit on the hub, make sure to press it down into the tabs. Shimano says to tighten the dust cap to 5-6 N-m. The dustcap is made of plastic, don't over tighten it. ...The threads on the dust...

Tool for plugging/unplugging SD-EW300 wires for the new Shimano/Dura-Ace 8100/9200 Di2 wires. ... Have tested with EW300 wires (non-I) and seems to work like a charm!

If you've disassembled a set of Shimano M324 pedals and find yourself unwilling to purchase the specialized tool required to secure the outer cone while tightening the locknut, consider this solution. It's engineered to fit snugly around the 13mm...

This tool installs and removes Shimano bottom brackets, replacing the outdated TL-FC24 and TL-FC25 adapters. ...Designed for use with Shimano BBR60 and BB-MT800 bottom brackets, it requires a 1/2" or 12.7mm square drive impact wrench to get the job done...

I required an instrument to tighten my Shimano crank bolt securely, therefore I designed and built this easy adapter to change to a hex driver. It fit perfectly onto the crank on the initial attempt. ...Enhanced with a circular shape for grasping...

I'm constantly misplacing these 2 tools, so I made a holder with magnets to stick on onto my metal pegboard. I also glued one next to my keyboard in the service area. I have spots for two 3x8mm round magnets. I melted in a chain pin into the...

A CAD file of the crank replacement tool was optimized utilizing Abaqus software, targeting affordability for printing. ...Despite its lightweight appearance and creation on an inexpensive 3D printer, it exhibits remarkable stiffness with a weight of...

I customized this tool to match my torque wrench perfectly. Only a handful of individuals will have a wrench that operates within the 0.5 - 1.5 Nm range, but I've included it for anyone who might need it anyway. ...I also reengineered it for easier...

Remixed with some flanges removed to make it printable without supports.