Solarbotics L298 Compact Motor Driver Mounting Plate 3d models

The Tough Box Mini motor gearbox, manufactured by andymark.com, features a surface mounting plate; this part is also available for purchase separately at andymark.com (part AM-2230). ...Andymark.com offers more information about the Tough Box Mini...

The holes are countersunk so the screws fit better and allow for a slightly thicker/stronger plate. The motor mount is designed similar to this thing, but technically not real remix of: http://www.thingiverse.com/thing:14507 Also shown is a front...

Mounting plates for E36 Sedan rear strut brace

Mounting Plate with Wheels for X-Axis, NEMA 17 Compatible

This thing enables mounting a NEMA-23 motor onto a NEMA-34 motor base. Instructions Print it with 0.2mm layers, and 50% fill, without any brim or support material required. I created this setup so I could test a screw drive...

This is a motor mounting plate for the Turbine Blower from johnnyrobot. The attached stl is for a motor with 25mm distance of the mounting holes. ...This can easily be changed in the also attached freecad file.

This mount will fit a titan 775 brushed motor into a slash 2wd. This ONLY works with the Hot Racing transmission housing or full transmission. I had some clutch rubbing in the early stages of the project, but it is no problem as long as you shim the...

The Hemera is mounted and screwed on at the back see picture The mounting plate is mounted on the X carriage using the original screws that held the old extruder on (you will need to split the extruder from the stepper motor to access the 2 bottom...

The Hemera is mounted and screwed on at the back see picture The mounting plate is mounted on the X carriage using the original screws that held the old extruder on (you will need to split the extruder from the stepper motor to access the 2 bottom...

Mounting plate designed specifically for 13mm width microswitches commonly used in DVD chassis types, ideal for use with Isolt's Photon Laser Engraver or any other CNC assembly incorporating these drives. Mounting holes are M2 with a precise spacing...

Just a simple mounting plate. ...Used this to mount 30mm fan to a 40mm fan place.

**HC-SR04** Mounting Plate for Unmanned Aerial Vehicles (UAVs) and Other Robotic Systems. Note that these SR04 ultrasonic modules are not standard **SR04**, as they feature an additional PCB with an Arduino connection, designed specifically for...

SD card is accessible after opening the top case and it can be replaced without doing anything more. For USB connection (Octoprint or anything similar), I cut and soldered broken USB cable to the bottom side of SKR board (USB pins are marked there)...

A compact mounting plate designed to secure a rev trigger and switch combo, inspired by the Bobololo style rev trigger found on Thingiverse under reference number 2362063. The snug fit requires some careful arrangement of the plate's shape through...

OZiCrawL sprintjet 9 hacker motor adapter plate

... front 16mm and 19mm holes was a priority, although the rear three holes may be misplaced. The motor mount is likely to be fairly accurate, though its thickness might vary slightly. ...I focused mainly on accurately placing the 32.5mm apart holes.

I believe I used M3x25 bolts and nuts for the filament run-out and mounting and M3x14 or 16 for screwing into the extruder motor. ... Make sure to tighten the extruder gear before mounting the detector as you need access from below to get to the set...

Jumper R1 receiver mounting plate for a 30.5x30.5mm stack. ...Uses m1.4x5mm screws to secure top bracket to mounting plate.

This part allows you to mount a NEMA-17 motor on a NEMA-23 size mount. It's the only printable object I have ever uploaded to Thingiverse that I haven't printed yet, which is why there isn't any photo of it. Still, I'm confident that this simple...

Mounting plate designed to accompany the widely used XY-3606 5-volt voltage regulator, which typically lacks necessary mounting holes.

Package Contents: Mounting plate for drone/quadcopter applications Flight Controller Mounts (30x30): - Flight controller mount 30x30: Standard Plate Configuration - Flight controller mount 30x30_1-6: Plate with Spacer on One Side - Flight controller...

... of the SKR board (USB pins are clearly marked) and route it outwards towards your Raspberry PI. To keep your workspace organized and simplify cable management, consider routing all motor, end-stop, and display cables underneath the mounting plate.

I utilize Arca Swiss Mounting System and swapped out the Base for the Equatorial-Mount. The Arca Swiss is extremely common, so I believe others will adopt this too. As a resident of the Cologne area, I adjusted the angle to 51° (the latitude-based...

... system is also included, as well as an emergency off switch for both the 24- and 230-volt systems. The mounting plate features shielded terminals for stepper motors and comes equipped with wiring ducts that measure 20 by 30 millimeters in size.

A mounting plate for securing your battery pack dock so that it doesn't slide around.

Remix of Thermostat trim plate. ... Allows for mounting and with cutout for the wiring connection

A mounting plate for Caddx Vista for 30x30 stack. ... Printed of Nylon

Basic front mounting plate. ...With my old V6 I can now print dual color.

This is a mounting plate for Jeti's Central Box 200. ...

Here is my file of the small mounting plate for the frontbumper. ...