Stepper Driver Cooler 3d models

This assembly provides a cooler configuration for standard NEMA 17 stepper motors, accommodating a 40mm fan seamlessly. Designed to be printed without any additional support, a brim may still be necessary. After printing, the two vertical supports...

This is a slim and significant lighter stepper cooler for a 40mm Noctua fan. It is lighter because it works without screws. In my tests the stepper is not geting warmer than 45°C. The shaft with the drivegear stay at nearly the same temperature. Even...

This is a slim and significant lighter stepper cooler for a 40mm Noctua fan. It is lighter because it works without screws. In my tests the stepper is not geting warmer than 45°C. The shaft with the drivegear stay at nearly the same temperature. ...

... ... This is a slim and significant lighter stepper cooler for a 40mm Noctua fan. It is lighter because it works without screws. In my tests the stepper is not geting warmer than 45°C. The shaft with the drivegear stay at nearly the same temperature.

A DXF file for a L6208 stepper motor driver module, incorporating component values recommended in the datasheet, is provided. Additionally, OpenSCAD files enable the creation of two mold negatives from which silicon rubber can be cast to produce a...

One to house the stepper drivers (uln2003) and RJ45 keystone jackclip, and one to house the RJ45 keystone jackclip alone. The standalone jackclip case is intended for the GPS/leveling modules and driver modules for the 2 steppers. The collection (2x...

I made adjustments to the base to accommodate the ULN2003 Driver Board, reducing its size for a better fit. The new dimensions are: 38mm x 34mm x 5mm. You can download two STL files - one is an ASCII file and the other is a binary file. Upon...

This is a straightforward slip-on cooler designed for your Makerbot Replicator 2 Nema 17 Stepper (Y-Axis). The cooling is powered by a 40mm fan, which helps to maintain optimal temperature during printing. Fan specifications include a 40x40mm size,...

It makes use of 2 x aluminum heatsinks with small fins to get them screwed to the clamp and holder, plus thermal pads to be put in between the heatsinks and the steppers to help them run cooler. Obviously, you could always stick them using...

It appears the stepper drivers were cutting in and out due to high temps. I then replaced the fan with a Noctua 40x40x10 (AF-40x10 FLX. As this is a 12V fan, i used a LM2596 DC-DC Buck Converter to reduce the 24V to 12V. I mounted this up and the...

If you want to align or set your stepper motor drivers, you'll need a cheap but hard-to-find non-conductive tool made from plastic or ceramic. Fear not - this works as a substitute: I designed and printed one using PLA. The design includes Phillips,...

Craft a 5.6cm x 5.6cm board for Pololu A49883 Driver, and follow the soldering instructions provided in the eagle file for proper assembly.

A cold air intake for the stepper heatsink fan on the Comgrow/Sovol T500. ...This fits tightly over the board fan and draws cool air in from under the printer.

The lens holder incorporates a stepper motor mount for effortless lens focus adjustment, accommodating an Arduino Stepper with a diameter of 28mm. ...Compact in design, the total dimensions of the module measure 95x95, making it easily integrable...

This is a friction fit DIN mount for a Gecko 320 driver and others that use the same size chasis. ...It is designed so that the wire input faces to the left (90 degree to the DIN rail)

I have an early 3 digit serial number Tormach 1100, and needed to upgrade the drivers. This bracket should allow for the conversion. ... Using Qty:2 M3 Heat press inserts ...

I was shocked to find that nobody had modeled the G540 driver from Gecko. I needed it for a project so I modeled it up using the Gecko Users manual dimensions along with some measurements from my G540. It is in STEP format. ...With and Without Cables to...

I was shocked to find that nobody had modeled the G540 driver from Gecko. I needed it for a project so I modeled it up using the Gecko Users manual dimensions along with some measurements from my G540. It is in STEP format. ...With and Without Cables to...

Hola a todos, Es un pequeño accesorio para poder colocar los drivers, que se puedan poner y quitar con comodidad. ... Para más información podéis entrar aquí y ver la caja que hice para mi CNC https://wp.me/p8xiic-k9 Y esta es la CNC ...

Support for a 50mm fan, specifically designed to cool the step-by-step motor drivers mounted on the CAMTOOL CNC V3.3 board provided with the Woodpecker CNC 3018. ...No special care is required for mounting since it replaces two original spacers; use two...

Adoption of 32-bit DSP, pure sine wave subdivision technology.Low-noise, low-vibration and low temperature rising.Voltage 18-50VDC.With 8 stalls output current setting, current range 1.0-4.2A.With 15 stalls microstep subdivision setting.Automatic...

Adoption of 32-bit DSP, pure sine wave subdivision technology.Low-noise, low-vibration and low temperature rising.Voltage 18-50VDC.With 8 stalls output current setting, current range 1.0-4.2A.With 15 stalls microstep subdivision setting.Automatic...

This bracket was custom-designed by me for my CTC i3 printer, which had been skipping steps and I discovered that the issue was caused by overheating TMC2100 drivers cutting out. If you have a standard GT2560 board installed, this is a great solution...

Hello everyone,\r\n\r\nIt's a small accessory that allows you to place the drivers, which can be easily put on and taken off.\r\n\r\nFor more information, you can click here to see the box I made for my CNC.\r\n\r\nhttps://wp.me/p8xiic-k9\r\n\r\nAnd...

The Leadshine MX3660 is a cutting-edge, 3-axis digital stepper drive featuring DSP technology. Designed for seamless control of up to three 2-phase (1.8°) motors in NEMA 17, 23, 24, and 34 frame sizes, it boasts a wide input voltage range of 20-60VDC...

This component serves to effectively chill the UP Mini Stepper's, specifically designed to accommodate a 50mm fan that optimizes cooling for the motor when printing with PLA filament. ...The precise spacing between the holes is set at 40 millimeters.

This installation needs a stepper damper (or a 6mm spacer), as there is end-switch connector in the way otherwise. I used Noctua 4020 fan (5.5CFM compared to 7CFM of the original fan), but it would fit (probably) any 40mm fan, no thicker than 20mm...

my bottom stepper motors really got quite hot: roughly around 60°C - and that shouldn't normally be a problem, but to get the most power possible out of my Nema stepper, i came up with this clever little fan mount. prints in a snap without any...

Hey Since the stepper motor of the Y-axis is always so extremely hot, I designed a bracket for the motor to cool it better and to keep the temperature low. I used a 4020 Sunon fan, any other 4020 fan works too. ... In order to get a better stability I...

I designed a new cooler for the Sidewinder X1 that takes in a standard 40x40 fan. ... I used this one here:...