Wire Strain Relief for Printrbot Simple Metal Heat Bed Modification 3d models

Print Settings Printer Brand: Printrbot Model: Simple Black Features: • No Raft: A Good Idea For Most Users • No Support: Great For Prints With Simple Geometries Printing Resolution: Set to 0.3mm Layer Height for Smooth Finishes Infill Percentage:...

I had to swap out the heated bed on one of my Ender's and opted for the Gulfcoast Robotics Aluminum Build Plate and 24V 200W Silicone Heater over some cheaper knockoff beds from China, which were similarly priced. The only snag is that the wires...

... can prolong the life of your cables and prevent any potential issues caused by frayed or damaged wires. Investing in a quality M10x1 strain relief is a smart move for any individual or business looking to maintain their equipment in top condition.

This project is intended to work with a custom filament guide that can be downloaded from Thingiverse at this link: https://www.thingiverse.com/thing:2341066 The touch LCD screen used in this project is available for purchase on Amazon at this link:...

... with FTC robotics in mind. ...Strategically placed holes are designed to accommodate REV extrusion seamlessly, providing a secure fit that's further reinforced by an extra layer of protection - additional holes for added safety and peace of mind.

This custom phone strain relief is engineered specifically for a permanently attached USB micro-B extension cable - tailored for a Moto G4 play with a case that matches the one included in the FIRST FTC kit featuring the Rev Robotics hub. To print...

Create a printable strain relief for your Cupcake's HBP by following these steps: first, print the provided design; second, slide it onto the heated build platform; third, secure wires in place using zip ties; finally, benefit from enhanced...

I made a plate to enhance my Build Volume Upgrade on the Printrbot simple metal 1403, allowing for about 290mm of travel on the Y axis. The plate bolts directly to the back of the arm, extending the mounting holes outward. To install it, you'll need...

... install a longer power cord for the machine. The original cable is actually fused to the inlet part, therefore the cable inlet has to be replaced along with the cable. The inlet and its strain relief are tight fits for cables of 8mm outer diameter.

The main function is to provide an anchor point for the HBP cable bundle on the Y-stage's right side, while also relieving strain from the X-axis endstop cable. By replacing the original two 1/8 inch spacers that hold the X-axis endstop in place,...

I merged the camera mount from https://www.thingiverse.com/thing:2818559 with the X-axis strain relief from https://www.prusaprinters.org/prints/24284-mk3s-x-axis-strain-reliefcable-protection to create a more stable platform, safeguarding the...

Horizontal Spool Holder and Filament Guide for a Printrbot Simple Metal with Optional Handle. Stepped cones are designed to fit most common plastic spools and utilize 608ZZ bearings, which feature a slight press fit. The bracket employs a 5/16 x...

However, this design was optimized specifically for use with the Printrbot Metal Plus (1412). To print your spool stand, you'll need four standard 608 bearings and nothing else except possibly sandpaper. The bars in my spool stand are designed to...

... the aluminum plate mentioned earlier. Tighten the screw to complete the installation. The M212 Z setting should be adjusted to around -.6 to -1 carefully, as failure to do so may result in damage to either the new hotend or the bed of the Printrbot.

I used these as strain relief / washers for M3 Socket Head Screws I was using on a printed quadcopter. I disliked the way the screw heads were compressing the PLA so I printed these in ABS to distribute the load evenly. I also designed them in a...

The Printrbot Simple Metal Spool Holder (http://www.thingiverse.com/thing:322923) necessitated PVC piping for construction. Given my reluctance to venture out and conduct any cutting, I opted to print the rods instead. This approach enabled really...

This camera mount is specifically designed to work seamlessly with both Logitech webcams and the PrintrBot Metal Plus 3D printer. Its primary function is to enable remote monitoring of your prints in real-time, allowing you to keep a close eye on the...

I use these to stabilize my PrintrBot Simple Metal and as a mounting structure for my Pi noIR camera. They can be seen featured with my Pi noIR Case with Spotlights. Printer Settings Brand: Printrbot Model: Simple Silver Rafts: No Supports: No...

You can use this adaptor mount if you have a Printrbot Simple Metal and want to fit in the 40mm Compact Fume Extractor, as shown in a related remix. ...Version 2 places it higher up, possibly requiring a more powerful fan for effective operation.

----------------------- Strain relief for the switch housing NAOM KA0-10KH I created the strain relief because there was no strain relief included in the package of the switch housing. It is suitable for flexible cables with 8 mm outer diameter. An...

X-Axis Wiring Strain Relief Instructions Print Heat with lighter Bend at proper length Remove screw on printer Get longer screw, 12mm long; original is 9mm long Attach with zip-tie or twist-tie to support and wiring V1 & V2 for zip-tie V3 & V4 for...

The Ipex part number TSRC101/2 is for a plastic strain relief designed specifically for use with electrical boxes, featuring a secure metal locknut to keep cables in place.

The inlet and its strain relief are tight fits for cables of 8mm outer diameter.Print SettingsPrinter:Flying Bear Ghost 4Rafts: NoSupports:NoResolution: 0.2 mmInfill:50%Filament: any PET-G (but PLA should do, too)...

Hermit Crab Strain ReliefI made a strain relief that holds the wires really solid and in a vertical position to allow maximum height clearance.I used two M2 heat inserts in the top to holes to attach.  I feel like you might be able to use the same...

New Strain Relief for Ender 5 aluminium plate to mount the Hemera direct kit.

Cable strain relief for lamps. Thread M10 x 1.

A typical Ethernet patch cable features a standard rubber strain relief boot for protection.

Here' s a spool holder for the Printrbot Metal Simple, using 1/2" PVC pipe to perform the primary tasks. It supports 1kg spools and smaller. It also works nicely as a handle, with or without a spool of plastic attached. For various holding options,...

M85049_38S9x STRAIN RELIEFM85049-38 Straight Strain Relief Clamp D38999

M85049_38S15x STRAIN RELIEFM85049-38 Straight Strain Relief Clamp D38999