Z braces for Wanhao Duplicator i3 Cocoon Create and Maker Select 3d models

Eyeballing the distance between bed and leveler should be good in most cases, but if there's not much range to the screws, adjust your Z axis couplers and then tweak the bed leveling screws. Check bed level at each Y end of the bed, as a minimum,...

I created this remix because the end switch on my 2.1 model is located differently than the original design, which results in misaligned mounting holes. Additionally, the area intended for adjuster placement was too close to the motor, making it...

... the z axis endstop. ...Its creator remains unknown, but users have successfully downloaded it from the wanhaoUSA website and installed it with ease. ...This adaptation serves as a convenient reference point for those seeking a practical solution.

I've carefully crafted these templates to calibrate the Z-axis perfectly by relating its leveling directly to that of the Y-axis for maximum precision.

... process of calibrating the Z-axis. ...A makeshift spirit vial was crafted using an old, inexpensive torpedo level that I happened to have on hand - these components are likely universal and easy to obtain. ...Standard equipment was utilized throughout.

I Am Sharing This Handy Item For The Purpose Of Aligning Your Z-Axis In Case It Ever Goes Wonky Or You Simply Want To Double Check It. I Recommend Printing Two Copies. ... A Note Before You Begin: If One Side Of Your Z-Axis Doesn't Budge At All, Even...

These parts are for a reverse bowden setup and a foot for mounting the spool holder at the bottom left side of the gantry. ... https://youtu.be/ax-nGRjBshU

The Z-Brace rod design is based on a turnbuckle principle - each rod extends and contracts when turned clockwise or counterclockwise. Once adjustments are complete, simply tighten the counter nuts at each rod end to eliminate any minor play and...

I tweaked the Saber filament guide to make it rock-solid and snuggly nestled against the printer's frame, allowing the entire assembly to sit comfortably on top of it and eliminating any unwanted stress or tension.

I remixed Saaber filament guide to be more sturdy and closer to the printer frame, in addition the arm sits ON the frame, freeing it from unnecessary strain. Category: 3D Printer Accessories

I used this rear fanduct: https://www.thingiverse.com/thing:1246425 alternatives are: https://www.thingiverse.com/thing:2004629 https://www.thingiverse.com/thing:1090433 Using this cooling setup, you get multiple benefits: - the nozzle stays visible...

This tool holder holds your most used tools like the 5 allen keys, calipers, pliers, scissor, USB SD card reader, feeler gauge and conveniently mounts to the spool holder holes. You will need two M5 screws with ~12mm length, but be careful if...

... time. To replicate this solution, you'll need longer M2 screws that are specifically designed for use with 4mm spacers, which are already installed in most standard configurations. ...The stock screws just aren't long enough for optimal alignment.

A custom mounting solution is being created to securely hold a BIQU MKS 1.5 control board within the power supply enclosure of a Maker Select V2 or Wanhao Duplicator I3 printer.

The Monoprice Maker Select V2 is essentially a rebranded Wanhao Duplicator 3, but it's not a bad printer for the price considering current options. I purchased this printer a long time ago as my first one. Unfortunately, they have a poor print...

It attaches to the bottom-front of the Wanhao Duplicator i3, Monoprice Maker Select, and Cocoon Create. It functions exceptionally well for a centered view of the bed. ... https://redd.it/52zunm Print Settings: Printer: Monoprice Maker Select v2 Rafts:...

... Lifecam HD-3000 in place. To replicate the look and feel of the original product, you'll need to incorporate parts directly from the original design. ...The provided art is merely a cosmetic overlay that sits on top of these underlying components.

The Monoprice Maker Select V2 is a rebranded Wanhao Duplicator 3 and they are not terrible printers for the price although nowadays there are much better choices. It was the first printer I bought quite a while ago. However, they share a TERRIBLE...

... adhere well enough. This part should be printed without supports, but if you opt for supports, you might achieve a slightly smoother finish on top. I have a cable cover on my 5/16" Z-brace and found that even without a screw, it fits perfectly.

Added mounting holes to @Malolo's screw-less / snap fit Raspberry Pi 4 Case & Stands and @Malolo's screw-less / snap fit Raspberry Pi 3 Model B+ Case & Stands so that I could mount it to my MP Maker Select Plus (aka Wanhao Duplicator i3...

This serves as a cover for the very bright LCD on the power supply of a Maker Select and many other models that share this exact design. Crafted on a Maker Select V2.1, I chose not to utilize supports. A piece of filament is used in the hinge to keep...

... visual confusion in the accompanying images. Print Settings Printer: Monoprice Maker Select V2 Rafts: Doesn't Matter Supports: No Infill: 100% Notes: I opted for 100% infill to maximize strength, though it's unclear if this is strictly necessary.

I just scored a Duplicator 2.1 from Microcenter and I'm checking out all the awesome mods available. This one caught my eye, but I've heard it produces a bad hum. I'd like to try increasing the surface area to minimize the humming noise while keeping...

It attaches easily to the bottom-front of popular 3D printers like the Wanhao Duplicator i3, Monoprice Maker Select v2, and Cocoon Create, providing a centered view of the print bed. ...For optimal results, ensure the camera is mounted in a fixed...

I designed a simple camera mount for my Wanhao Duplicator i3 with Z brace mod installed because HillbillyZT's mount wouldn't work with the Z brace modification. I came up with my own design. This mount is compatible with any standard 1/4"...

I love the original design - it's truly exceptional! ...I've relocated it to the right-hand side of the printer, which works perfectly since my MKS Gen L board is already installed on the left side.

A Simple Camera Mount for Wanhao Duplicator i3 with Z Brace Mod. Since HillbillyZT's mount wouldn't work with the Z brace mod, I designed my own. This camera mount is compatible with any camera featuring a standard 1/4" tripod mount, but it was...

A simple camera mount for a Wanhao Duplicator i3 that has the Z brace mod installed. HillbillyZT's mount wouldn't work with the Z brace mod, so I designed my own. This is compatible with any camera that has a standard 1/4" tripod mount, but I...

A fully 3D-printable spool mount is designed specifically for the Duplicator i3 Plus / Monoprice Maker Select Plus. It utilizes Emmett's high-quality printable gear bearings to create a rolling platform for the spool, ensuring smooth filament...

Following the lead of FilamentCorner's z Brace and z Extensions (Z-Kit), I decided to make a hybrid design that moved the braces to the back of the printer so as to be out of the way. All of this is based on AzzA's original work which can be found...