a 10 bracket 3d models
2355363 3d models found related to a 10 bracket.
thingiverse
Here are some add-ons to help beef up the vert stabs. All items can be printed without supports. I attached with hot glute but do not put glue directly onto the 3d printed parts. ...Put the glue on the foamboard first then press on the parts.
thingiverse
I cant speak for the A-10 since I dont have one. That model has 2 lights and I'm not sure how close they are together, so I dont know if 2 of these printed pieces will properly fit beside each other. Layer height, material, and infill amount (no...
thingiverse
A very simple bracket to hold the Raspberry Pi in a Smraza Pi Model 3 B - multi-layer case on top of my CR-10. ...
grabcad
Design created for GE Engine bracket challenge, removed after I got disappointed about results. ...But it is a beautiful design, so I'll re-publish it.
cults3d
Fairchild Republic A-10 Thunderbolt II, single-seat, twin-turbofan, straight-wing, subsonic attack aircraft, 1976
thingiverse
Basically what I'm saying is I'm not exactly holding my breath for this to get featured or anything, but man if you need a bracket that just happens to be of these proportions, I have you covered. ...
thingiverse
... version of http://www.thingiverse.com/thing:1038261 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1038261 Instructions Using the following options: zRotation = -45 xTranslate = 50 wholeMessage = /a/ zScale = 10
thingiverse
This is a Mounting Bracket to bolt down or screw down a CR-10 3D Printer.
thingiverse
This is a replacement T-Bracket for the right side of the CR-10. ... It was designed to be similar to the stock one.
thingiverse
T-Bracket for my CR-10 Mini (I was missing one...). The holes are not aligned to the Z-stop bracket, I suggest it be used on other side. I print with 100% infill for strength. ...
cults3d
This is a bracket to let you put a flexion extruder on your CR-10. Make sure you have a pass through coupler for the bowden tube so the tube makes contact with the flexion. That is what stops the filament from bending and escaping the extruder. ...It...
thingiverse
This is a bracket to let you put a flexion extruder on your CR-10. Make sure you have a pass through coupler for the bowden tube so the tube makes contact with the flexion. That is what stops the filament from bending and escaping the extruder. ...It...
thingiverse
I have a CR-10 S5 and bought the Z-axis support kit from Creality. First off it wasn't long enough, and second I stripped the end hole you are supposed to tap for 5mm threads. I designed this in Fusion 360 to work with M5x12 bolts and M5 T-nuts to...
grabcad
A little simpler and less organic than my previous entry ' GE-Bracket-09'. Mass / Volume is 23.7% of the original, giving a 76.3% reduction in Mass/ Volume. ...There are holes underneath the network of support tubes to let the un-fused metal powder...
thingiverse
After upgrading my printer with a BMG clone extruder, the Z rod was hiting the extruder. I made this bracket so it turns the extruder and steper 90º. Also left some space to add a cooler on the steper. ...As you can see on in the pictures.
thingiverse
10 bay variant of the SSD Stack0r by h3nkGer which was a revision of the original 2/4 SSD mount by colanabo. ...Approximate dimensions are 94.5mm x 10mm x 119mm
prusaprinters
Wanted a 10 bay version of the original SSD Stack0r for my server. Simply print 2 of these and install SSDs with HDD screws. ...Can either attach with screw holes on bottom or go the easy way like I did and stick it to the bottom of my server chassis...
thingiverse
When you upgrade certain parts, the T-nuts are not required anymore (Y-axis tensionner) and you can take them for the T-Bracket. Print the part like it shows up when you open the STL file (flat). ...You can print it at 0.2mm layer height and at 100%...
myminifactory
This takes your TUSH (The Ultimate Spool Holder - https://www.thingiverse.com/thing:2047554) and allows you to easily mount it on top of the CR-10 control box. I love being able to move the TUSH anywhere on my desk but there are times I wanted to...
thingiverse
This takes your TUSH and allows you to easily mount it on top of the CR-10 control box. Hmmmm, that came out wrong. ;) In case you don't have this wonderful spool holder already, find it here: https://www.thingiverse.com/thing:2047554 I love...
cults3d
This takes your TUSH and allows you to easily mount it on top of the CR-10 control box. Hmmmm, that came out wrong. ;) In case you don't have this wonderful spool holder already, find it here: https://www.thingiverse.com/thing:2047554 I love...