a1 upper receiver 3d models

this is upper handguard for AK-74U gel blaster. ...It uses for 3D printing

Customizable upper rear wishbone kit, fabricated directly from blueprints found in a trusted mechanical engineering handbook.

Upper arm piece for resin FW contemptors, modelled and tested and confirmed to match

Re-engineering Blower Upper Housing through the application of Solidworks software

Upper Plate Module Divided into Three Distinct Areas, Accommodating XT60 Modular Plug Connectivity

It is an upper and lower I found it on Onshape

Weight-shift upgrade kit featuring an upper battery mount for BMRx.

I made a optional upper frame for your 3DFly. ...Looks coll when attached properly

Prop AR22 Upper. ... Remix of https://www.thingiverse.com/thing:2948270 Added a clean side version

I was designing very specific Packout receiver to fit a toolbox and someone mentioned making a standalone universal receiver.  This receiver can be used in pairs to hang a full Packout box or standalone to hold items that only have one cleat.

This hitch receiver plug is designed for use with Class I and II receivers (1-1/4" x 1-1/4"). Initially, I conceived it with the intention that the cross would need to be painted on, but subsequently redesigned it so that the cross can be printed...

Measuring (excluding the USB port itself) 14.1mm x 6.4mm, my receiver performs flawlessly but may require some minor adjustments if your device is slightly larger. I've found it compatible with a couple of Logitech nano usb receivers, although...

You can check the Bluetooth receiver board here: https://www.parts-express.com/sure-electronics-aa-ab41136-bluetooth-40-audio-receiver-board-aptx--edr-12-vdc--320-351. I've been using this board for over three years, and I'm impressed with its sound...

Additional to the flightcontroller you need an RC-receiver that works with your transmitter. You don't need a lot of range so use a old or a crappy one. To protect this devices i've designed a box. Betaflight CLI command: set usb_hid_cdc =...

The paper cover around the receiver needs to be removed. Low tolerances. ###A lot of labor went into my designs. Designing, printing, testing, redesigning, retesting, .... I share my designs for free and love seeing people downloading them and...

The components that the support is tailored to are: Receiver: FrSky X-Mini or FrSky R-XSR VTX: AKK for stacking Barometer: BMP280 To secure the VTx, I employed the standard nylon nuts with M3 screws. ... (Note: This output has a Flesch-Kincaid grade...

Here are the essential components I employed: The Monitor A generic 5.8GHz FPV Receiver This mount should seamlessly integrate with other models as well. To complete the setup, you will also need a versatile 1/4" to 3/8" Convert Screw Adapter for...

3 different RC Receiver mounts for Spektrum AR410, AR630 and AR631.The 410 has very little clearance and can slip loose on a hard landing, but it does not support ASX and SAFE, so this should not impact flight. Velcro tends to allow the receiver...

To keep the receiver dry and clean, protect it from dirt like sand. It's not completely waterproof, but if you seal it with the same grease or silicone rubber, I think it will be waterproof. Just close all the holes that maybe water can go into the...

I got tired trying to keep all the wiring from getting into the servos and creating a tangled mess in my Dynam Primo RC Plane, so I came up with this clever solution - a tray that holds the receiver above the servos and protects them from all the...

I designed this Xbox Wireless receiver holder for my PC because I was fed up with it constantly falling off my desk and disappearing on me. I added a clip at the front of the receiver holder so that I could easily locate it after using the USB port...

This compact piece replaces the spacer situated beneath the top rail in the handguard, and fits snugly into a small hex-shaped hole in the receiver during assembly, preventing the handguard from rotating inadvertently and loosening the barrel nut. ...To...

This is a unique opportunity for the Falcon Receiver.\r\n\r\nThere are two distinct options available for the base, one that perfectly aligns with the holes on a CG1500 box and another option without the tabs specifically designed for the CG...

I used to simply attach the receiver PCB with 3M UHB tape, but I recently ran into a situation where I needed to remove the electronics from a model to perform some repairs. The tape did its job too well and I decided to re-mount the Rx so it could...

The product can be found on Aliexpress at the following URL:...

Purpose ----------- Glue this [receiver](https://youtu.be/Nr3KBPUWL10) on the back of foamcore, mirrors, or other lighting modifiers for a quick and easy way to mount using a baby plate. ... Compatibility ----------------- Fits the [Impact 3" Baby...

Needed a FPV test monitor to bench test video transmitters, so I removed the display from my Hobby King Quanum Goggles and added a receiver to the back of it. This is the enclosure to keep it decent looking and power from XT60 connector. ... Category:...

I've been using a mini stand to elevate my Logitech G930 wireless receiver and boost its signal strength. It's a small but effective accessory that keeps my gaming experience smooth and uninterrupted. ...The compact design of the stand makes it easy to...

I created a compact enclosure for my e-board project, specifically engineered to safeguard both the receiver/transceiver and the wattmeter while also allowing for secure installation of the wattmeter itself through a transparent window that offers an...

This SKS Receiver is from the 3-14888, GRAU (56-A-231) Technical Data Package. We plan on modeling the entirety of the sks from this package if there is enough support for this project. ...Special thanks for dale's conversion of gost to iso.