a10 model

Case runout sensor filament genuine Geeetech A10 https://youtu.be/SXra5cUiGBw ------------------- Look at this my project! ... https://www.thingiverse.com/thing:4623521 Follow me please for more projects ;) https://www.thingiverse.com/duegi/designs ...

A fine fellow named combat341 on the Geeetech A10 forum figured out that you must activate the following comment in the firmware: #define FAN_SOFT_PWM...take off the backslashes to make it active. This is all it took for me to get PWM control. I...

... Additional components needed: 4 M4x6mm screws 4 T-Nuts M4 Optional: LCD Display Holder Left Side Geeetech A10: https://www.thingiverse.com/thing:4098947 Silicone damping feet with adjustable height: https://www.thingiverse.com/thing:4108039

I replaced the mainboard of my A10 and decided to use sensorless homing (with TMC2209 stepper drivers) instead of mechanical switches. So I needed to replace the X/Y micro switch end-stops with a bumper. Both bumpers consist of two parts: One none...

On the left side of the A10 there are 2 small holes where the cables can be hidden well. The LED strips are connected either: - at the lower case fan (24V): The LEDs switched on directly with the printer. - or to a free bottom fan. Then the...

This cover fits perfectly over the LCD of my Geeetech A10 printer. I recently attempted to print one of the covers found on this site, but encountered an issue - the connector for the display on my printer was off by about 1.5 centimeters, situated...

Rocker switch covers for A10 CDU, The dimensions are taken from original cdu. Stil you must to adjust them for better fit. Opaque resin is good choice for printer if you have a resin 3D printer. Sure you can print them with "wire" 3D printer. Then...

This is for the first version of Geeetech A10 printer. It serves as a replacement part for X endstop and stepper motor mount. All measurements are identical to the original piece, but this one is crafted from wood. I'm unsure if it will function...

I adjusted the rear casing to match my screen since it was initially misaligned with mine.\r\n\r\nMy Geeetech A10, acquired in January of 2019, comes equipped with the GT2560 v3.\r\n\r\nThe other two components are genuine products.\r\n\r\nIt fits...

This is a replacement for the spring-loaded latch that goes on the extension tube of the Tineco A10 (or A11) Hero vacuum cleaner. I have had two of them break, so I think it's a design issue with the original. ...This part is a direct replacement that...

First, when I received my Geeetech A10 3D printer, I was fed up with the lousy fixing of the filament runout detector (with a spherical nut). So, I designed a fixed support to hold the detector in place. But then, the built-in "ear" fixation broke...

Tensionneur de courroie pour axe X sur Geeetech A10 & A10M, compatible avec d'autres modèles d'imprimante.\r\nIl est facile à installer et ne nécessite aucune visserie, écrou ou boulon supplémentaire.\r\n\r\nPour imprimer avec succès, suivez ces...

I decided that I really needed a fan guard for my Geeetech A10 after chipping off a couple fan blades on the hot end, so I went Atari-Style, of course! This is not an example of dual extrusion printing, the orange color is just from a paint marker. I...

This remix takes an outstanding design by jdharris and adapts it perfectly for 1st and 2nd gen A10's where the part cooling fan is situated on the right side of the enclosure. ...The innovative approach to the stock duct is truly remarkable.\r\nI'm also...

Custom-hotendmount for GeeeTech A10 / A20 with stock-hotend and custom-fanduct for 2 404020 blower.Printing in PETG or Extrudr GreenTecPro is recommended.Use the stock-hotend and turn it around. ...Use M2,5 and M3 screws, washers, nuts.</p><p>Supports...

Thunderbolt A10 Voici déjà le 10ème avion de la série : le célèbre Thunderbolt A10, un avion américain d'attaque au sol. Le kit compte 8 pièces précises et détaillées. Comme tous les autres avions de la série, il se présente comme une carte de...

**Files:** - **Geeetech A10 Version 3 Y-Axis Support.stl - Back.stl** - The support for the back side - **Geeetech A10 Version 3 Y-Axis Support - Front.stl** - The support for the front side. **Parts Needed:** - **12 x M5 12mm button top hex...

This is my custom upgrade for the Geeetech A10, offering an improved design with the cooler fan relocated to the side. I prefer this setup as it provides a clearer view of the print nozzle. Some additional hardware is required for assembly. To...

I figured it was high time I added a fan guard to my Geeetech A10 after mishandling the hot end and chipping off a couple of fan blades, so I decided to go old-school Atari-style! This isn't about dual extrusion printing; the orange hue is simply...

This is a cover I made to protect my Thrustmaster A10 HOTAS Joystick Base when my joystick is removed. As the connector is exposed when you have the joystick removed, I wanted to make sure that no dirt, dust, liquids or any other paraphernalia...

After experimenting with various cam mounts for my A10, I was unable to find one that provided stability without shaking during printing. Consequently, this mount, which attaches underneath the bed, came into being. It also doubles as a convenient...

Boquilla de ventilación para Hellbot Magna I o Geeetech A10 - A20 con fan de capa 5015. La Boquilla a pesar de ser unidireccional, tiene una concentración del flujo de aire que lo hace mucho más eficiente, es corta de tamaño para reducir las...

Geeetech A10 2018 Cable Clamp If you print this thing and find it useful, please consider hitting either the "Tip Designer" button to the left or the "Donate Now" Button below and help share the love and support more designs like this one. Thank you....

i printed and used the feet from MHprints they worked and fitted my A10 perfectly but after a month the feet had sagged so losing all support. They are one of the best options out there so i decided to add some yellow bed springs for extra support. ...

I adapted a mounting plate for the GEEETECH A10 printer. The mount is designed to work with the bowden version of the aforementioned extruder/hotend. After installing the hotend, two bottom screws become inaccessible due to a genius design; however,...

I love that mount for the E3D V6 for Geeetech A10. I have modified the original design by adding a face plate which add lots of rigitity. I also include the frame of a fan for those using a single fan. This frame can be used instead of the second...

This is an updated version of Merlin699's straightforward filament guide for Geeetech A10 printers. I enhanced the mount height by 13mm to ensure alignment between the roller and the entry hole of my BGM style extruder. The rest of the components...

i printed and used the feet from MHprints they worked and fitted my A10 perfectly but after a month the feet had sagged so losing all support. They are one of the best options out there so i decided to add some yellow bed springs for extra support.

This is a Cable Management Solution for Geeetech A10 printers. The electric cables of the print head have been damaged multiple times due to excessive X-axis movements, causing frequent interruptions. A simple device prevents these cables from...

This is a remix of Merlin699's small & simple filament guide for Geeetech A10 printers. I increased the height of the mount by 13mm to align the roller the with the entry hole of the BGM style extruder that I have fitted to my machine. All other...