a6 upgrade 3d models

new front brace to get rid of the acryl plate ,

annoying contact with reset button in middle of print? simple solution ,tiny ring glued with some silcone,didnt used superglue because of risk ,adding some on the button itself !! ... simple soluting for the z axis belt ,works way better now the...

A little upgrade for my A6 with the 32 bit SKR V1.3 and TMC2208. A new X-Axis with IGUS bearings and a printed Z coupling with no wobble. Prints nice! You need 4 IGUS bearings (2 ech side). All parts from the Anet can be used in the new design.

I have this tunnel designed as an upgrade for a 40mm fan so the fan on the printer extruder head doesn't get too much warm air gets in while cooling to filament during the printing process. You need both files 1x printed to use this upgrade. Please...

I have this tunnel designed as an upgrade for a 40mm fan so the fan on the printer extruder head doesn't get too much warm air gets in while cooling to filament during the printing process. You need both files 1x printed to use this upgrade. ... Please...

This extruder heatsink support tubes will eliminate the unnecessary bending tension on the empty side of the heatsink of the Anet A6's extruder, caused by the screwing solution. *Don't forget to multiply the object or to print it twice as you will...

Print Settings Printer: Anet A6 Rafts: Doesn't Matter Supports: Yes Resolution: 0.25 Infill: 15% How I Designed This This project was one of my most difficult projects I have made. I have everything measured out well so that everything fits perfectly...

Ras

This is an enclosure for an Anet A6 that (tightly) fits: * [MKS Gen v1.4](https://amzn.to/2Qqir47)\* * [Mosfet](https://amzn.to/2EblQfB)\* * [Raspberry Pi 3](https://amzn.to/2E89QM5)\* * [3A Buck converter](https://amzn.to/2QLiGGi)\* I upgraded my A6...

This is an enclosure for an Anet A6 that (tightly) fits: MKS Gen v1.4* Mosfet* Raspberry Pi 3* 3A Buck converter* I upgraded my A6 to a MKS Gen v1.4 as it was the simplest (and cheapest) route to upgrade the stepper drivers and get some TMC2130*...

Amount you need: 1x Stabilizer-Bracket-Front.stl 2x Stabilizer-Bracket-Middle.stl Please feel free If you like this model and you want to support my work that I am making, you can donate me if you want with paypal:...

This is the tensioner for the X axis so that you can easily x axis can turn tighter. You will need a couple screws and nuts: 1x M3 40 mm 1x M3 30 mm 2x M3 nuts Instructions: You need to get right side of the X-axis almost completely apart so you...

I didn´t like the way the belt slides along the sharp edges on the A8 so i created this thing! Also Reduces chances of belt wobbling/vibrations=Increases print quality. Have fun! ...:p Print Settings Printer: Anet A8 ...

ANET A6 UPGRADE to SKYNET 2.3.2 AUTO for CURA 2.6.2 Start : G21 ;metric values G90 ;absolute positioning M82 ;set extruder to absolute mode M107 ;start with the fan off G28 ; Auto Home All AXIS G29 ; Auto Bed Levelling M84 ;steppers off M0 S12 ;wait...

If you have problems with the size, you can contact me and i will make a smaller version for it :D I have made this upgrade for my Anet Anet A6 and A8 3D printers to get the X-Belt to make it easy tighten it up. Two friends of my asked me to make one...

If you have problems with the size, you can contact me and i will make a smaller version for it :D I have made this upgrade for my Anet Anet A6 and A8 3D printers to get the X-Belt to make it easy tighten it up. Two friends of my asked me to make...

If you have problems with the size, you can contact me and i will make a smaller version for it :D I have made this upgrade for my Anet Anet A6 and A8 3D printers to get the X-Belt to make it easy tighten it up. Two friends of my asked me to make...

110V users probably want about a 6A fuse, but feel free to consult with a proper electronics expert in your area. Print Settings Printer: Anet A6 Rafts: YesSupports: No Resolution: 0.2Infill: 100 Notes: Printed at 0.2 or 0.1 and 100% infill. ...

An improved holder with increased stability. ...Some report a very tight fit so it might be necessary to print it at 98% Get the screw and the plate from the original inventor Photograaf16 (Anet A6/A8 upgrade: Y-Belt tensioner)

I have this designed to allow print my printer stable. with this design, you can easily put your printer on a flat surface with six bolts and nuts. it's very easy to fix, you just need your components through threaded bars to the correct position...

Power Supply Cover to be used in conjunction with 360W PSU which I purchased at Banggood - https://www.banggood.com/Wholesale-12V-30A-360W-Switch-Power-Supply-Driver-for-LED-Strip-Light-Display-220V110V-p-39987.html?rmmds=search&cur_warehouse=CN . ...

this is a Backplate for the tensioner holder (https://www.thingiverse.com/thing:2006595) by using bolt and nut from hardware shop.

Please feel free If you like this model and you want to support my work that I am making, you can donate me if you want with paypal: https://www.paypal.me/JordanHogetoorn Print Settings Printer: Anet A6 Rafts: Doesn't Matter Supports: Yes Resolution:...

This model I designed because sometimes I had some problems with humidity or dust that sometimes came into the extruder. This model is for 1.75, 2.85 and 3mm Filament. You will need to use this Filament filter all parts 1 time(FilamentFilter_Side_1...

4mm Aluminium Template: https://www.thingiverse.com/thing:2125534 adapted for ANET A6

... Have a good day and don't forget to leave a comment if it helped You! You can watch my review of Anet A6 here: - https://www.youtube.com/watch?v=zxlTGkgWEfU And my video about upgrading it here: - https://www.youtube.com/watch?v=KauVa8hqxtw

... bed on the high side. The Posi-Drive Leveling Upgrade syncs the two screws with a timing belt, guaranteeing that the extruder and bed remain level for the life of the printer. ... Upgrade kits and full BOM available at http://3dwrx.com/anet.html

**Safety First!** The Anet A6 kit has dangerous main power terminals exposed without cover, fuse or on/off switch. This simple power supply cover will make your 3D printer more safe to operate. **To assemble you will need:** * 2x M4 6mm...

Safety First!The Anet A6 kit has dangerous main power terminals exposed without cover, fuse or on/off switch. This simple power supply cover will make your 3D printer more safe to operate.</p><p><strong>To assemble you will...

It's working.