a8 fan 3d models
122244 3d models found related to a8 fan.thingiverse
This is a remix between the stock Anet A8 fan duct and the semi-circular fan duct. In my opinion the direct air flow is the best but design of the stock fan duct is flawed and result a whistle. ...Here I have fixed this problem.
cults3d
This is a remix between the stock Anet A8 fan duct and the semi-circular fan duct. In my opinion the direct air flow is the best but design of the stock fan duct is flawed and result a whistle. ...Here I have fixed this problem.
thingiverse
This is a part that allows you to mount the Anet A8 side fan and the heat sink to the extruder block using the two existing screws. This is a tight fit, which is what I wanted. You may need to enlarge it by 1 or 2%. ... Printed using PLA
thingiverse
Anet A8 original fan duct. This is a Remix (made from scratch) of ms3dp's fan duct, because his neck is to short.http://www.thingiverse.com/thing:1438439 Note that the support is only in the neck so you can remove it. The model is rotated so the...
thingiverse
An inlet shroud / duct to slightly improve the efficiancy of the standard Anet A8 cooling fan.
thingiverse
This is my remix of bartoaster's Anet A8 Fan Hinge! ... I really liked this mod but printed it twice and it always broke at the neck, so all this remix does is reinforces the connection to the hinge!
thingiverse
This is a remix / improved version of the "Anet A8 Fan Holder by Lion31" this anet a8 mod allows you to change your filament easier then with the stock fan holder that comes with the anet a8. ... the improvement i made to Lion31's model is a blocker at...
cults3d
Improved Anet A8 Fan Duct. This has a semi-circular design in order to not interfere with the heater block wires, and an optional stem that prevents the fan duct from falling off mid print. Tolerances around the stem join are 0.1mm, so it is a...
thingiverse
Mount for original Anet A8 nozzle fan with cable management for Jeka_tm beautiful and simple E3D v6 mount. https://www.thingiverse.com/thing:1824307 Can be used with original duct or with "Spriya" which I can highly recommend.
thingiverse
Anet A8 Extruder Nozzel Fan Cover This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/iwYR1xWr9mp
thingiverse
Hey, this is a fan cover i made for my Anet A8, nothing special just trying to make it look better.
thingiverse
A friend of mine needed a spacer for his extruder fan on his Anet A8 3D printer. I made this in a few minutes in OpenSCAD and decided to post it in case anyone else needs one. The plate is for a 40mm X 40mm square fan with a 38mm diameter fan. It...
myminifactory
This is a fan duct for the Anet A8. ... I had to design a custom one, because I'm not using the stock nozzle. This design is about 10mm taller than the other models I've seen here.
myminifactory
... with a deeper blower connection and a slightly longer nozzle to be slightly closer to the hot end. Some dimensions from this model originate from Original fan duct for Anet A8/Hesine/M505++ by mseljestokken - http://www.thingiverse.com/thing:1438439
myminifactory
This is a remix of two objects. They contain the best of both worlds and the logo isn't slightly crooked. There is increased airflow(less resistance) and they match(Yaay!) Designed specifically for the A8, but will work on any 50mm centrifugal...
thingiverse
Improved fan for Anet A8. I have some problems with parts that have overhang zones and even with the circular fan that I print the problema persist, so I design this part and it solved my problem. ...It has a wider exit and different angle from the one...
thingiverse
... everyone, there goes my first contribution;). I hope you find it useful. 80mm fan holder for the electronic board of the Anet a8 printer. Caution, it is necessary to change or cut the original electronic board spacers, for about 11mm. ...Thank you.
thingiverse
Hola :D Esta es una mejora para el Fan o Blower que hice para mi Anet A8, ya que los "picos" combencionales a la larga me daban muchos problemas y se soltaban del Blower para el extrusor. Que mejora esto? : 1- mayor superficie de la pieza es...
thingiverse
I've created a Fan Mount for my ANet A8. I wanted something that moves out of the way easily. This design removes the Heat Sink and turns the fan around so it blows IN OVER the assembly and exhausts past the stepper motor. I used the same 3mm screws...