acrobrat frame v2 3d models

Printed replacement for the standard aluminum frame widener.

The modular underwater robot known as MiniROV utilizes a state-of-the-art dc motor thruster system labeled as V2.

Which is a change from the old engraver: larger working area for the laser part (355X360 instead of 310X315) symmetrical foot, easier and faster to print right and left slide are interchangeable and easier to print lectern not integrated in the...

New Frame Upgrade for Enhanced Diatone 250 Version 2.2 Performance

This is an official reference guide for creating custom accessories compatible with the Zypher frame.

Second iteration of a handgun designed for Frame Arms Girl models.

Raspberry 7" LCD display frame and holds the PCB at the rear Adjustable angle for the display using screw bolts Display frame is backward compatible with V1 Display = 7D-CPT-TV-50PIN PCB = PCB800099

I originally made this frame using the existing Shendrones Squirt Parts to test fit TPU ducts and for further planning.

This is an updated design on PI D-Frame Case Due to issues with access to side ports

This remix is specifically designed for the aluminium frame version with extra support under the top frame to prevent the support from popping off. It can be easily modified to fit other types of frames. ...The bottom sections on both sides can be...

I used v1 acrobrat ducts from gaunch0, fine-tuning motor mounting holes and seamlessly integrating two together to fit the frame perfectly. I relocated wire routing cutouts for a smoother setup. With precise calculations, I printed two sets...

... fc and triangular vtx fixed on top. Battery is fixed below. 14x14 micro fpv camera Change in V2: the V1 suffer from jello on fpv cam, probably due to the petg filament. ... I've modified the fpv cam cage, now it's more rigid, and printed in PLA.

I'm revamping my ANET A8 frame upgrade for the second time, opting instead to create a fresh page and sidestepping the hassle of updating individual components on the outdated version.

Changes: - Increased standoff-hole spacing to ~ 38mm to fit an Acrobrat Duo - Moved Immortal-T cable hole to the side to allow clipping it in - the part that opens up is blocked by the frame when assembled - split the holder for the T-part of the...

It isn't highly improve the print quality but increase the frame rigidity and also you can force the vertical beam to perpendicular to the base with the nuts.Bill of materials:* M10 threaded rod - 100 cm* M10 nut - 8 pcs* M5x10 - 8 pcs* M5 hammer...

I've got a revamped version of the Strike Frame, all polished up after tackling that pesky spike problem - I'm pretty sure it's resolved now! ...I beefed up those spikes too, making them bigger and badder, while also adding some extra flair to make 'em...

You can simply drop it in place or do what I did and use a couple thin strings of blue sticky tack along the bottom of the flat outer frame. ...I purposely designed it to have a slight bit of wiggle room (<0.2mm) so you should not have to make any...

To assemble the face shield frame, push the center peg through the hole drilled earlier, then gently tuck the two edges into the frame. Secure the assembly with one or two large rubber bands, positioning an ear guard in between. ...The design...

This brilliant solution effectively addresses a key issue with Prusa I3: excessive freedom on its vertical frame. Although my own version of Prusa utilizes 10mm threaded rods, not 8mm, this meant I couldn't employ Wingman94's parts directly. In...

You can simply drop it in place or do what I did and use a couple thin strings of blue sticky tack along the bottom of the flat outer frame. ...I purposely designed it to have a slight bit of wiggle room (&lt;0.2mm) so you should not have to make any...

These components simplify and streamline the integration of the DJI FPV System Air Unit and camera into the Ummagawd Acrobrat Duo 3-inch frame. ...I have provided models to either install the DJI antenna beneath the rear rotor arms, offering a...

XT30 plug designed for the acrobrat duo with NO 3d print in the rear section of the quad (ie GPS module or antenna) Uses stand off for support

Human: Custom Mount for the AcroBrat Drone, Featuring TBS Unify-Style SMA Connector and Adjustable 3mm Antenna Tubes at a 45-Degree Angle.

My take on an Insta360 Go camera mount for the Ummagawd Acrobrat 3 inch quad. Inspired by 4noxx' https://www.thingiverse.com/thing:4461347 and angled back by around 27°. ... It's also a camera standoffs replacement for the 20mm FPV camera.

No description is available for this character.

The human element is what sets us apart from technology. It's the spark that ignites creativity and brings passion to our work. Without humans, innovation would stagnate and progress would grind to a halt. We're not just machines; we're the ones who...

Quicker Than Expected, This One Was Picked Up To Hold The Lead In Place Against The Frame. Utilize The Existing Screw For Attachment. ...Thanks A Lot!

Ender 3 v2 Frame Blacking Caps

For Betafpv X_Knight 5 V2 Frame,Cam basekit

This mount is compatible with other cameras that are 19mm wide, including the Caddx Turtle - you can now fit both a Runcam Split Mini and a Caddx Turtle on an AcroBrat frame at the same time. No support needed; print using a layer height of 0.24 mm...