adafruit bno055 3d models

... the caps are printed in PLA or other filaments that don't shrink. Design Process: We created this design using Rhino 3D by modifying a pre-existing model from the Adafruit website, the PiGRRL 2.0: https://learn.adafruit.com/pigrrl-2/3d-printing.

A horn extender for Adafruit Large Ultrasonic (Sonar) Sensor or something like that from e.g. D.F. ...robot or Akiduki Denshi.If you have unstable responses from soft surfaces, have a try.

Case for Adafruit PowerBoost 1000 Charger - High Capacity 5V Lipo USB Boost at 1A - 1000mAh. ...The sides are carefully crafted to make it easy to remove the battery connector.

Coarse Model of High-Quality Audio Effects Sound Card - Adafruit Part Number 2217. ... Perfect for Scaling Up Your Projects with Ease, This Dummy Component Is Ideal for Prototyping and Testing in 3D Printing, Computer-Aided Design, and More.

Outer (2/2) part of a case for Small IoT LoRa Weather station. ...You can get the inner (1/2) part here: https://cults3d.com/en/3d-model/gadget/adafruit-feather-m0-weatherstation-inner-case

Inner (1/2) part of a case for Small IoT LoRa Weather station (12x8x8cm). ...You can get the outer (2/2) part here: https://cults3d.com/en/3d-model/gadget/adafruit-feather-m0-weatherstation-outer-case

Upper (1/2) part of a case for Small IoT LoRa Parking slot sensor. ...You can get the bottom slider (2/2) part here: https://cults3d.com/en/3d-model/gadget/adafruit-feather-m0-range-sensor-bottom-slider

Bottom slider (2/2) part of a case for Small IoT LoRa Parking slot sensor. ...You can get the upper (2/2) part here: https://cults3d.com/en/3d-model/gadget/adafruit-feather-m0-range-sensor-upper-part

This is a Minimal Case for Adafruit nRF Sense Feather. Includes space for a 500 mAH battery. ...If the lid is printed in transparent PLA or similar, the neopixel colour and brightness can be seen through the material.

A speedy DIY remake of peeter123's Adafruit Huzzah Feather Case. Check out pictures for installation orientation. ...Flip or mirror it if you prefer it facing the opposite direction!

The USB C connector is not the exact same, this is meant to be an estimate (hopefully good one) of the board, pin locations and mounting holesitem: https://www.adafruit.com/product/4090

Just a simple proetctive case for Adafruit's PN532 Breakout v1.6.Includes slots in the base for easy storage of 25mm round NFC tags and 54mm wide NFC cards between RFID hack sessions.

Adafruit's Raspberry Pi Zero Case Features a Sealed-Off GPIO Header. ... The casing is showcased here, printed on the Anycubic Photon using Clear Eco Resin at a 50-micron layer thickness.

Here is a mount for an Adafruit DRV8833 board to fit between the legs of an ESP32. Works really well with my other ESP32 mount for the SMARS v4 chasis. ... https://www.thingiverse.com/thing:5207566/

Housing build for Adafruit MCP9808 Temperature Sensor. With attached OpenSCAD file everything is customizable, especially size of screws to close and size of opening for connection cable. ...But can also easily adapted for other breakout boards.

Nice little stand for the Adafruit Funhouse. It features two sensor mounts to float more input over the house. 4 M3 screws for the Funhouse. 4 M2.5 screws for the sensors. ... Enjoy!

This is a simple bracket which adds a Modular Mounting System compatible hinge to the back of nlapenn's case for the Adafruit Macropad. ... Secures to the back with two M3 screws.

You can purchase this Beagle Bone accessory from Adafruit shop at http://www.adafruit.com/products/702, along with other great Beagle Bone accessories available at http://www.adafruit.com/category/75. Remember to support open-source hardware by...

ZMR 250 front or rear holders for Adafruit Neopixel 8 Print Settings Printer Brand: RepRap Printer: MendelMax 1.5+ Rafts: Does Not Apply Supports: Does Not Apply Resolution: 0.2 to 0.3 Infill: 80 Percent

A din rail mount for an Adafruit Cricket. You will need to print one tabs for this design. ... It can be found at: https://www.thingiverse.com/thing:3401942

This project involved constructing an enclosure for my Raspberry Pi, which was operating under OctoPi software. ...The display used was a 2.8-inch TFT LCD screen from Adafruit, complete with integrated touch functionality.

This custom enclosure wraps around an Adafruit Feather 32u4 FONA, enabling a Power Monitor setup that instantly sends a text alert whenever electricity supply is disrupted. ...Detailed tutorials will be available on GitHub shortly.

... of the component in order to prevent it from free-spinning. Based on: https://www.thingiverse.com/thing:4907617/files For use with: https://www.adafruit.com/product/5128 My other designs for this product: https://www.thingiverse.com/thing:5185595

A drag race style display using Adafruit's seven-segment backpack display (https://www.adafruit.com/product/878). This display uses the I2C bus, so multiple displays can be controlled using just four wires. I have included parameterized...

... satellite platform. By leveraging the resources provided by the Cubesat's design, you can integrate the Adafruit screen seamlessly, creating a truly cutting-edge system that combines precision engineering with user-friendly interface capabilities.

CAD Model of Adafruit LCD Backlight Module (Product ID 1622) The CAD model in question is based on the Adafruit LCD backlight module, specifically product ID 1622. This particular component is manufactured by Luckylight under the part number...

This case for the Adafruit MacroPad is a snap fit enclosure and requires no additional hardware.Layer height 0 .2Should be sliced with “Detect Thin Walls” so the tips of the snap tabs do not make gaps in the walls.If you are using the Adafruit...

This ingenious accessory is designed specifically with the Adafruit Pi fan in mind, which can be found at https://www.adafruit.com/product/3368. ...The case itself is also available online and can be easily sourced from Thingiverse at...

The standard DIN rail mounts don't really have good mounting locations for the Adafruit feather board. ...This print provides the adapter.</p> <h3>Print instructions</h3><p>Very straightforward print.</p> <li>0.15 mm layer height</li><li>40%+...

This is a remix of an LDO Mini Afterburner ADXL mount to work with an Adafruit ADXL which has wider mount holes. M2 self taping screws used to hold Adafruit ADXL to mount. Two existing Mini Afterburner M3x35 button head screws need to be swapped for...