adafruit feather enclosure 3d models

Working on an enclosure for a feather stack, first proto, no top

Adafruit Feather Box Enclosure

This was edited from the model found in [this video.](https://youtu.be/XRc24yu4dpk) I edited this to make the lid fit with more of a pressure fit than relying on screws/inserts. This is for mounting to your garage door opener to turn it into a...

Simple enclosure for holding the Adafruit Feather Tripler. ... Please note that I'm using 2.5mm threaded inserts for the mounting screws.

YouTube: https://www.youtube.com/watch?v=jy7a-z19UEQ ***NEW UPDATE*** April 8, 2016 – Added new parts for Adafruit 2.4" TFT Feather Wing This is our 3D printed case for the Adafruit Feather. It’s for anyone looking to put their project in a box. It’s...

YouTube: https://www.youtube.com/watch?v=jy7a-z19UEQ NEW UPDATE April 8, 2016 – Added new parts for Adafruit 2.4" TFT Feather Wing This is our 3D printed case for the Adafruit Feather. It’s for anyone looking to put their project in a box. It’s a...

Each part has different versions, so you can make it better fit your project and there’s no wrong way to configured it. Full Tutorial: https://learn.adafruit.com/3d-printed-case-for-adafruit-feather/overview Print instructionsLicence: Creative...

A simple enclosure to hold the Adafruit Featherwing doubler board and a small 2000mAh LiPo battery. ...The enclosure also has holes on the sides that you can use to mount an Adafruit QWIIC sensor.

This is an enclosure for an Adafruit Feather that features an opening for a 1.44" Color TFT, Vibrating Mini Motor Disk, SPST Slide Switch, 3.7V LIION Battery (all from Adafruit), and two momentary contact switches with switch cover. The enclosure...

Print in TPU for a soft case or PLA for hard case. Print at 0.2mm layer thickness to get exactly two layers of material for the diffuser screen. The small knobs on the diffuser screen might need a bit of cleanup after the print. ... If the knobs...

This is a remix of the pretty cool Adafruit Feather enclosure adjusted for the Adafruit Feather LoRa 32u4 RFM95. The original box did not fit the Feather with soldered on uFL connector, this box should :) Furthermore I added a cable holder, that can...

This should fit to the 128x32 OLED (https://www.adafruit.com/product/2900) and feather wing boards with short pin headers

Modded the micro usb plug hole to fit Adafruit ESP32 Feather V2 usb c with tinkercad

This model will house the following assembly: ( With soldered on header-pins / See photo ) Adafruit Feather HUZZAH with ESP8266 WiFihttps://www.adafruit.com/products/2821 NeoPixel FeatherWing - 4x8 RGB LEDhttps://www.adafruit.com/products/2945 With...

I designed and modeled enclosure case for a stacked Adafruit Feather HUZZAH and Mini Relay FeatherWing. You'll need to use the short headers for this stack. Here's the parts for this stack: - [Adafruit Feather HUZZAH with...

Adafruit ESP8266 Feather.

model 3D Adafruit feather HUZZAH

stl model for adafruit feather nRF52840 Sense

Adafruit Feather HUZZAH ESP8266, CAD model

Case for the Adafruit feather: doubler: https://www.adafruit.com/product/2890 oled: https://www.adafruit.com/product/4650 motor controller: https://www.adafruit.com/product/2927

YouTube: NEW UPDATE April 8, 2016 – Added new parts for Adafruit 2.4" TFT Feather Wing This is our 3D printed case for the Adafruit Feather. It’s for anyone looking to put their project in a box. It’s a multipurpose enclosure, so you can use it...

Use these for case design and the ilk.* 128x32 Display: https://www.adafruit.com/product/2900* Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500 https://www.adafruit.com/product/3010

... Adafruit (P/N: [2796][Adalogger]). The logger specification sheet can be downloaded from [here][AdaloggerSpecs] [Adalogger]: https://www.adafruit.com/product/2796 [AdaloggerSpecs]:https://learn.adafruit.com/adafruit-feather-m0-adalogger/downloads

A case with mounting holes for the Adafruit Huzzah Feather. ... Donate: BTC - 3EaaHt38KPUjsRTL2oewUToYbc41V1TEZm ETH - 0x3685734d8ca2Ea59462c77711A7430Bf2b573b38 DGB - DNVxnasDtYsiDAi7nExZCSApA5yTLWCE9H

**Adafruit Feather Puller** by [Nathan Robinson](https://nrobinson.me) This tool can be used to quickly pull Adafruit Feather Boards out of breadboards. I created it to assist people with removing Adafruit Feather Boards from breadboards without...

Adafruit Feather case designed to have a BNC bulk head and powered via USB. To Secure the Feather use M2.5 Screws inserted in the bottom of the case with a washer/nut on the feather board. ... Case will work with any of these boards:...

Complete CAD Model for the Adafruit Feather ESP8622 including all SMD parts and decals.One version with pinheader and the other without.More Infos here:https://www.adafruit.com/product/2821

This is a rough model of the Adafruit Feather STM32F405 Express board with only several major components. Apply the p2m or png files to the top and bottom surface of the model for more detailed visualization. ...Buy it from Adafruit:...

- Male/Female Short Headers for Feather boards (https://www.adafruit.com/product/2940 and https://www.adafruit.com/product/3002) - Adafruit's Breadboard-friendly SPDT Slide Switch (https://www.adafruit.com/product/805) - 200-400x20 mm Strap (e.g. ...

Frame holding Adafruit Feather Bluefruit BLE microcontroller.STL and step files contain what you can see on a picture with a model (it's missing that extra custom part I made for my keyboard). ...Real photo is just to show fit of microcontroller as I...