adafruit pi camera 3d models
138485 3d models found related to adafruit pi camera.prusaprinters
I wanted to be able to use a Raspberry Pi Camera with Octoprint for remote monitoring of my printer using this mount, however the longest compatible FCC cable I could find for the Pi Cam and Raspberry Pi Zero was 30 cm. This is not long enough...
thingiverse
I have the adafruit pi camera v2.1) Created this from scratch with the mount holding the camera solely by friction, and it fits TIGHT. I also made channels for the LED lighting on both sides so it can be mounted in either front corner. Angled at...
thingiverse
The mount is designed so that the [Adafruit Raspberry Pi camera mount](https://www.adafruit.com/product/3253) slips in and locks into place. It is made to hold the back bracket, **without** the clear cover. I did this because in my experience, the...
cults3d
The mount is designed so that the Adafruit Raspberry Pi camera mount slips in and locks into place. It is made to hold the back bracket, without the clear cover. I did this because in my experience, the cover interferes with the camera's focus and...
grabcad
Adafruit raspberry Pi case with HITMAN logo on top and adafruit industries, LLC at the bottom Raspberry Pi model at Raspberry Pi A made by clear acrylic 3mm thick note: not finished yet, haven't add the hole for the Pi
thingiverse
This is a combination of several Raspberry Pi case models, all based on the Adafruit case. ... I have tweaked the thickness and tabs so that little, if any, trimming is necessary before assembly.
cults3d
I had to make some small tweaks to get it to cut right from Inkscape and while I was at it I added the Raspberry Pi logo to the lid. ... I also made the slots a bit thinner to better match the 0.093" acrylic that I found at my local hardware store.
thingiverse
This is a redesign of the Adfruit Pi Cam Tripod. The original was a great design, but I wanted to change it up a little. The bolt on the top is now part of the back, instead of being separate. The hole on the back is smaller now, which fits...
thingiverse
I had to make some small tweaks to get it to cut right from Inkscape and while I was at it I added the Raspberry Pi logo to the lid. I also made the slots a bit thinner to better match the 0.093" acrylic that I found at my local hardware store. ...
thingiverse
Header cover for the Adafruit Raspberry pi zero acrylic case (https://www.adafruit.com/product/3252)
thingiverse
Adafruit Pi fan adapter for octopi case for the Monoprice Mini Select V2 Pi fan: https://www.adafruit.com/product/3368 Case: https://www.thingiverse.com/thing:2198704
cgtrader
Adafruit raspberry Pi case with HITMAN logo on top and adafruit industries, LLC at the bottomRaspberry Pi model at Raspberry Pi Amade by clear acrylic 3mm thicknote: not finished yet, haven't add the hole for the Pi
thingiverse
A case i made for my pi running octpi with the 2.8tft+touch from adafruit
thingiverse
Note that 2 front panels are provided for the conventional pi camera and the wide angle camera. Ventilation can be improved by trimming the corners of the 30x30 fan and gluing it to the back plate. The ventilation will be more efficient at the...
thingiverse
Four minor revisions to Ben Rockhold's Extended Raspberry Pi + Adafruit LCD Case: Enlarged USB port for easier cable connection. (bottom half) Added standoffs for screw mounts in RPi Model B. (bottom half) Increased clearance for connector at...
cults3d
Adafruit IoT Pi Printer Project Pack - Enclosure http://www.adafruit.com/products/1289 Adafruit invests time and resources providing this open source design, please support Adafruit and open-source hardware by purchasing products from Adafruit! ...
cults3d
You can find the instructions here:http://www.built-to-spec.com/blog/?p=1971 If you don't have a laser cutter, you can grab one of these cases from our store...
thingiverse
You can find the instructions here:http://www.built-to-spec.com/blog/?p=1971 If you don't have a laser cutter, you can grab one of these cases from our store...
prusaprinters
Replaces the Pi mounting plate in the Adafruit IoT Printer kit. The new plate(s) have screw holes that fit a Pi Zero. Versions for M2.5 or M3 Screws. Versions for either a solid plate or a basic frame design. Category: Electronics
thingiverse
Simple Raspberry Pi and Adafruit Ultimate GPS HAT. Designed for a Pi 3B+. Additional hole in the side of the case for the optional SMA to uFL/u.FL/IPX/IPEX RF Adapter Cable adapter for an external antennae. ... 4x 2.5mm X 11mm F/F standoff 4x 2.5mm X...
thingiverse
Replaces the Pi mounting plate in the Adafruit IoT Printer kit. The new plate(s) have screw holes that fit a Pi Zero. Versions for M2.5 or M3 Screws. ... Versions for either a solid plate or a basic frame design.
thingiverse
A very quick & dirty first attempt at a simple stand for a Pi 3B, in the style of the delightfully simple yet aesthetically pleasing Pi Zero stand from Adafruit; https://learn.adafruit.com/raspberry-pi-zero-stand/ I wasn't necessarily expecting this...
thingiverse
Adafruit IoT Pi Printer Project Pack - Enclosure http://www.adafruit.com/products/1289 Adafruit invests time and resources providing this open source design, please support Adafruit and open-source hardware by purchasing products from Adafruit! ...
thingiverse
This is stand to hold up the Raspberry Pi in the case I designed earlier that holds the Raspberry Pi with the Adafruit PiTFT screen. It holds the RaspberryPi at a 60 degree angle for easy desktop viewing of the screen. Prints in three parts that...
prusaprinters
This is stand to hold up the Raspberry Pi in the case I designed earlier that holds the Raspberry Pi with the Adafruit PiTFT screen. It holds the RaspberryPi at a 60 degree angle for easy desktop viewing of the screen. Prints in three parts that are...
thingiverse
I occasionally have to turn a drill bit by hand in the board holes a little to shave out just enough for it to fit, which of course is not recommended by Rasperry Pi or Adafruit. I really wanted to use M3 bolts in the way that I did, so I'm OK doing...
grabcad
Aesthetic model1:1 Scalehttps://www.adafruit.com/product/3421
thingiverse
# Description Very rough model of the Adafruit 16x2 LCD Pi Plate. Useful as subtraction for creating cases for the LCD panel. See the [Servotester](https://www.thingiverse.com/thing:3968126) as example. # Usage (in OpenSCAD) 1. Create model...