adafruit ultimate gps hat for raspberry pi 3d models

I had this HMTECH brand (generic) Raspberry Pi screen 7" that uses HDMI and USB. While it has a VZBot logo and was made for my vzbot, it should work with any screen that is similar to size than the HMTECH (different brands have the same hardware) and...

This is another take on the raspberry pi camera mount, specifically designed for mounting on an athorbot couple frame. However, it can be used on any device with holes that fit, and you can easily create new mounting points to suit your printer's...

I also printed a set of Lack enclosure parts for the right side leg so I could pass wires through that side as well. Hardware needed:(4) M3 x 8 screws to secure cover(or longer, up to 14mm)(4) M2.5 x 6 screws to mount Raspberry Pi(4) M2.5 screws...

Two straightforward brackets that securely attach your Raspberry Pi 2 (with case) to the top of your Prusa i3 MK2 power supply unit (PSU). This works well for an OctoPi setup. I'm using a standard 61mm x 28mm RasPi2 plastic case and these brackets...

I wanted to integrate OctoPrint into my Tornado setup and keep the Raspberry Pi hidden from view. To minimize the RPi case's height and avoid interfering with the build plate carriage, I adapted AlexSwensen's design by relocating the mounting tab to...

The Octoprint case sits lower than in the original position. Print instructionsCategory: 3D Printer Accessories Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 15% Notes: Print with...

I've designed a brand new frontplate for my Eleduino 7" 1024x600 TFT-Touchscreen, which I'm using in my Raspberry Pi-OctoPi installation on my Prusa i3 MK2. The original plate leaves some areas around the TFT uncovered, so you'll notice electronic...

A simple, easy Raspberry Pi Camera mount to attach to the top side of a 3D printer enclosure. This print utilizes 4xM3 screws which can face the printer at a 40° angle. ...The camera itself simply slides into the mount, and no additional fasteners are...

... a heat sink - feel free to omit it if you prefer - and also created an access port to smoothly accommodate a ribbon cable through. ...I selected the Adafruit PiTFT Plus 320x240 2.8" TFT + Capacitive Touchscreen for its exceptional performance.

I made a small back plate for my raspberry running octoprint. The holes are placed 58mm x 49mm appart so any raspberry will work. ... the left and right variant are made so you can place it in what ever direction you want

Case that holds a Raspberry Pi 4 and the Pi camera. Allows the angle of the camera to be changed in the vertical direction. Design primarily for OctoPrint. ... Check out my insta for more projects: @neyth_makes https://instagram.com/neyth_makes

Case that holds a Raspberry Pi 4 and the Pi camera. Allows the angle of the camera to be changed in the vertical direction. Design primarily for OctoPrint. ... Check out my insta for more projects: @neyth_makes https://instagram.com/neyth_makes

A simple 3.5mm jack plug to hold my Raspberry Pi into it's Octoprint case. The case itself doesn't have any clips or catches to hold the Pi securely in, but it does have ports. ...I don't plan to use the headphone jack, so it is a convenient place to...

This case is designed to house a Raspberry Pi 4, a 20Ah battery, USB accessories (like an RTL-SDR), and a 30mm fan inside a 3" PVC pipe. GPIO pins are accessible, making powering the fan or using GPIO peripheral simple and easy. The 3D printed...

My Raspberry Pi camera is enclosed in a Miuzei case that was sitting on top of my Lack enclosure. After almost knocking it to the floor a dozen times, I decided to design clips that allow me to mount it on the side of the enclosure. The clips are...

My Raspberry Pi camera is safely stored in a sturdy Miuzei case that was initially positioned on top of my Lack enclosure. After narrowly avoiding a dozen near-misses, where it almost fell to the floor, I decided to create specialized clips that...

I designed this bracket to work seamlessly with sneaks' Articulating Raspberry Pi Camera Mount and the CR-10. Initially, I found Top Bracket to be extremely stable when printed on its side, but unfortunately, I soon discovered that it requires a raft...

Just a Raspberry Pi Cam case with a GoPro mount... Print Settings Printer: Anet A8 Rafts: Doesn't MatterSupports: Yes Resolution: 0.2Infill: 10% Notes: Consider these printing parameters: -0.2 -10% infill -Wall thickness: 1.6 -Top/Bottom...

Wanted a stand to have the pi vertical for better cooling and smaller footprint on my desk v1.2 is the one I printed in the photo v1.3 has a cutout for the pi to be stood with the usb ports facing upwards without smooshing the sd card

I designed a custom holder for a Raspberry Pi Zero W that attaches directly to a Huawei B525s Router. The Pi will be powered by the Huawei router's built-in USB port, ensuring it stays energized at all times. My goal was to integrate the Pi with the...

Remade tray from scratch in Fusion 360 Smoother corners, bigger cutout. ...Reduced weight/print time. With same PLA weight got down from 12g to 7g. Version for Raspberry Pi and Oragnge Pi one Fully compatible with rack-mount bracket by russross

Just whipped this up to make sure I have measurements for the Pi Zero right and protect the traces on the back side of the board. Print it out, slap the Pi Zero on it and heat up a paperclip and smash down the pins of the case to secure it all...

Whipped up this design to ensure accurate measurements for the Pi Zero and safeguard its traces on the backside of the board. Print it out, place the Pi Zero on it, heat up a paperclip, and press down firmly on the pins of the case to secure...

Raspberry Pi Case with Pi Camera for Mounting on CR-10 This project combines several designs found on Thingiverse, and I take no credit for the original designs. Instead, I combined elements that I liked and made minor adjustments to make them work...

This is a screen/power supply combo for use with Raspberry Pis, Banana Pis or similar single-board computers. ... I used bjoerngiesler's touch monitor case (http://www.thingiverse.com/thing:298272) and parts from lima's monitor holder...

This remix simply adds space for the cpu heatsink, specifically the dimensions of ones provided by popular Pi kits by CanaKit. I didn't want to increase the height of the entire sleeve as I think that would ruin much of its aesthetic appeal. ... This...

After using this excellent sleeve design, I noticed adding heatsinks to the Pi (at least Pi 3 B+) would prevent the sleeve from fitting due to clearance issues.This remix simply adds space for the cpu heatsink, specifically the dimensions of ones...

So I wanted to add a Bright Pi to the articulating Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2 https://www.thingiverse.com/thing:3114849. I took the Bright Pi stl from the Bright Pi Camera Case thing and sliced it together with the...

This print was made to meet a specific need I had, but I thought it would be useful to provide the print as it has some useful design ideas.I needed to mount a Raspberry Pi enclosure to a metal post 3" in diameter, so I made this simple adapter which...

# Main features - Supports Arduino and Raspberry Pi out-of-the-box. - Extendable to custom boards, with support for NVIDIA Jetson Nano and Google Coral Dev Board being next on the list. - All sides have the same dimensions and hole positions to...