add on card pencil holder 3d models
1458588 3d models found related to add on card pencil holder.cults3d
Adapter to be inserted in the original support to have a thinner slot. ...Cards will no longer fall
thingiverse
Adapter to be inserted in the original support to have a thinner slot. ... Cards will no longer fall
thingiverse
English: It's an add on of 'SD Card Holder For Creality CR10 by rmlc460' project on thingiver You can use a Cable µSD to µSD instead of the µSD to SD Card Cable of initial project. (you must Choose/Buy the right Flex Extension cable as pictures...
thingiverse
I settled on this design: https://www.thingiverse.com/thing:123670 The only problem I have with it was that my public transit card would not be read through it. I had to find a solution to either bring the card closer to the reader, or make it easily...
thingiverse
Simple but effective spool holder add on. Inner diameter of thread is 33mm, length of thread is 80mm. ...
myminifactory
Simple but effective spool holder add on. ... Inner diameter of thread is 33mm, length of thread is 80mm.
thingiverse
Spool Holder - greatly improves the default one (much less friction) - you need four 4x8x8 [mm] needle roller bearings and two 4x83 [mm] rods - you can put it on top of the default spool-holder - use a 4x40 [mm] bolt (photo) to secure it - no nut...
prusaprinters
Simple but effective spool holder add on. Inner diameter of thread is 33mm, length of thread is 80mm. Print instructionsRafts: No Supports: No Resolution: 0.24 Infill: 10%
prusaprinters
Filament Spool Holder Add-On for 30mm Dia. ...Spool Holder greatly improves the default one (much less friction) you need four 4x8x8 [mm] needle roller bearings and two 4x83 [mm] rods you can put it on top of the default spool-holder use a 4x40 [mm]...
thingiverse
This is an add-on to the Dominion Card Carousel V1 made by Chainmaillekid. This adds a third row to allow three extra card slots for things like Platinum, Colony or Curse cards found in the expansions. ... This should be printed with support due to a...
thingiverse
With this add on for http://www.thingiverse.com/thing:2084482 stand to serve many different reel hole sizes (22-100mm) and quick swap The sharp point acts as bearing allowing even heavy reel rotate nearly with out the friction, the reel bed have...
prusaprinters
With this add on for http://www.thingiverse.com/thing:2084482 stand to serve many different reel hole sizes (22-100mm) and quick swap The sharp point acts as bearing allowing even heavy reel rotate nearly with out the friction, the reel bed have...
thingiverse
Communion Cup Holder D-1 (center of hole from bracket side - 5 mm) D-2 (center of hole from bracket side - 10 mm) D-3 (center of hole from bracket side - 12 mm)
thingiverse
I added a small part to hold 2" wide spools of paper towel. ...The small sections of paper towel are useful when cleaning the Prusa PEI print surface. Download the original models from Paper Towel Holder v2 https://www.thingiverse.com/thing:1526585
grabcad
The pencil and card holder is 3D printable. In the middle a drafting triangle can be placed. !the card holder is for plastic cards not business cards! ...Make the card holder somewhat bigger for business cards
thingiverse
A card/pencil holder I've made for a friend to put on his office desk. ...Recreated his logo and mostly added stuff on Blender and removed the girl because well...
thingiverse
Business Card and Pencil Holder. Large Pencil Holder fits lots of stuff. With and without the Gen 3 Engineering Logo. (Cura Tree Supports were used on the logo). ... CR-10S with E3D V6 / Petsfang 220 deg C first layer / 215 deg C nozzle 65 deg C...
thingiverse
This little Thing is an add-on for you apple pencil that makes sure it doesn't make a run for it when you put it on a flat surface. ...Print Settings Printer: M3D ...
prusaprinters
A MINI+ plate holder for 4 plates that can be used independentlyor attached to Filament Spool Holder 2021https://www.prusaprinters.org/prints/59013-filament-spool-holder- 4 Plates- MINI+ Plate form on the bottom to keep plates stable
pinshape
... apple pencil from rolling away and off your table. ...The apple pencil is completely round, which causes it to easily roll off (a design flaw, i would say). But now you can print this design, slide it on you apple pencil, and not lose it ever again.
cults3d
Pen and card holder with travel theme, roman colosseum and pyramid of mexico
thingiverse
I never use the usb slot on the tool holder so thought to add a holder extension for my torque wrench.
thingiverse
I never use the usb slot on the tool holder so thought to add a holder extension for my torque wrench.
thingiverse
Pen holder for the CNC.http://www.thingiverse.com/thing:724999 Flexible pen holder, has some give to it to keep even pressure on your surface. Uses 2 cable ties or similar to hold any size pen, pencil, marker. ...Print Settings Printer: ...
thingiverse
I've got an universal table holder from aliexpress. ...Unfortunately it is very difficult to mount it stable. This small add-on made from TPU fix the problem
thingiverse
its just a add-on sponge holder to madtag you need the main file to use this, link bellow https://www.thingiverse.com/thing:5233138
thingiverse
Add-on for Pickle_Rick_1's tool holder. I needed a place to store my pliers and calipers. ...This fits the 50mm wide power supply boxes.
prusaprinters
Pen holder for the CNC. MPCNC Flexible pen holder, has some give to it to keep even pressure on your surface. ...Uses 2 cable ties or similar to hold any size pen, pencil, marker. Print instructionsCategory: Machine Tools Print Settings Printer: MPCNC,...
thingiverse
Mask holder that adds on to existing light switch screws, was able to hold several masks without noticeable bending. ...Worked well in my university dorm during the COVID-19 pandemic.