adjustable post base 3d models

Manufactured Specifically for High-Quality Scratching Posts Utilizing Standard M8 Thread.

polished 316 stainless steel Card Reader Post (automatic door opener)likes are appreciated.

A template to determine the location of the posts on a Crokinole board I'm building.

This is a front sight post for an AK or SKS with a cone on top.

TA02 extended Body post for Tamiya 1:10 scale RC cars

Compact, scaled-down site featuring remnants of a post-Roman kiln facility.

A simple-to-assemble Guard Check Post ensures optimal security measures are implemented.

Assemble the parts of a square tool post to form a complete unit.

Square Tool Post modeling and dynamic assembly using NX v10.0

I'm signaling the end of my post for the Tronxy X5 printer.

Kid goal post made from 1" PVC pipe. ...Goal opening size 4' X 3'

Human is upgrading to the ultimate off-road machine - the Yokomo YZ-10 Body Post.

This is a front sight post for an AK or SKS with a cone on top.

Here is a small accessory that will allow you to store your post-its.

Wire tie post that slides into the gap in a PVC fence

A simple post it note holder. ...Made with 8 different slots.

This is a tower I made because I have too many post it notes.

The cap on my brother's post was metal and rusted away. ... This is a replacement.

-> Box for post-it (normal size : 3" / 6.7 cm) -> Designed on SolidWorks -> Sliced ​​on Cura

A Daisy-shaped holder for standard 3 inch post-it notes.

Fence Post Light for 12MM bullet Pixels. ...Requires 4 #8 3/4 Metal Screws

I have a post-it stand that keeps my three sizes of post-it notes tidy: 3" x 5", 3" x 3", and 2" x 1.5". I dislike dispensers where the pad is stuck into or to a big holder. Instead, I prefer to be able to move the pad itself around the office or...

Marbulous, Marble Genius, Marble Run, Toto Toys Standard Post 35mm h x 27.5mm dia, Boss 6mm h x 23.5mm dia Posts 100mm between center, 17.5mm I.D. tube, 4deg slope This model has 4 posts and measures 1 post high. I set the support overhang angle at...

Marbulous, Marble Genius, Marble Run, Toto Toys Standard Post 35mm h x 27.5mm dia, Boss 6mm h x 23.5mm dia Posts 100mm between center, 17.5mm I.D. tube, 4deg slope This model has 5 posts and measures 1 post high. I set the support overhang angle at...

Marbulous, Marble Genius, Marble Run, Toto Toys Standard Post 35mm h x 27.5mm dia, Boss 6mm h x 23.5mm dia Posts 100mm between center, 17.5mm I.D. tube, 4deg slope This model has 3 posts and measures 1 post high. I set the support overhang angle at...

This Porch Post Sleeve is used as a decorative cover for the bottom of porch post or similar structure. This two piece design eliminates having to jack up the porch to slip a traditional one piece design under the post. This version is for a 4" post...

It is intended to mount a tube, like a cardboard shipping tube, to the wall for use as a cat scratching post.Print 2 brackets, and mount each to the wall with two screws apiece. Insert threaded rods through the bracket arm holes and through holes you...

Why not make it the actual test?" So I remixed the cube to be used with post processing scripts to change my retraction settings every level. Now I can test different retraction settings on the same cube. The base is 2mm (10 layers at 0.2mm layer...

To print the post successfully, I recommend printing it with supports all over to ensure that the balls are fully supported by the base plate. After removing the supports, sand the areas where they touched to create a smooth surface for easy...

... with two M3 screws, body post is secured to the holder with one M3 screw. Requires: • 1 x 6 mm body post • 2 x short M3 screws (6~ mm) to mount the holder to the chassi rails/towers • 1 x M3 screw (10+ mm) to secure the body post to the holder