adjustable sensor mount 3d models

Here's a quick DIY model I whipped up to hang an Oculus Rift CV1 sensor on a wall. You'll need a 1/4-20 bolt to lock in the camera - a 3/8" length should suffice. ...To secure it to the wall, use small nails or brads; thumbtacks are not ideal for this...

... how I printed it) is that the tabs break off every time. So, I reinforced the tabs by adding material at an angle outside of each tab. The trick with this part is to bend the whole part when putting the sensor in rather that trying to bend the tabs.

When operating a temperature sensor through your wall, this protective covering shields it while allowing airflow to circulate around it. The built-in thermometer holder's design echoes the appearance of an old-fashioned thermometer face, and its...

This is a basic enclosure for a temperature and humidity sensor that allows you to monitor the internal temperature of your print environment. A low-cost option for acquiring this device can be found on Aliexpress for as little as $1. ...After...

This little beauty is a T-shaped bracket, serving as a bridge between Tetrix patterns and Modern Robotics sensors. With its robust design and cleverly added side supports, it's incredibly easy to 3D print. ...Perfect for FTC teams who need reliable...

This is a simple filament runout mounting plate for putting it next to the top mounted spool. ...It has holes for screws and v-slot nuts to mount it securely on the top of the gantry.

Then i decided buy a new clock based in battery, with indoor and out door temperature sensor and voltimeter. I don´t paste a link where to buy ir , but this model is famous in most of on line shops. ... I installed the part in to my fiat ducato...

Created by Team 2410, this mount is designed specifically for the MaxBotix XL?MaxSonar?EZ0.

this mount is used to connect the sick camera used in machine vision

i like the design, but it always come loose... ...so i modified it a little bit. now you need to bolt it on. after mounting the mount you need to level the printbed. ...

You will need to remove the sticky foam from the back of the sensor for it to fit. Also added a second screw holeI printed with these with the orientation as seen in the preview, i.e. base down. ...Was expecting the clip parts to break as the stress is...

Created to attach an 18mm diameter capacitive sensor onto my X-carriage was this setup, only it seems there is a strange mismatch of 24.5mm between the M3 bolts. After exhaustive research, one that fits could not be found so it had to be...

This is my very first custom design, created specifically to hold my blue-tipped proximity sensor securely on my Cobblebot V2. While others may exist, I opted for a design that fits perfectly without any modifications needed. Print Settings: ...

I designed this print, but it never saw the light of day because I upgraded to an 8mm sensor that performs exceptionally well. Print Settings: Printer Brand: My trusty RepRap printer is always up for the task. Printer: The Prusa i3 Hephestos is my...

Here are some alternative tools that can replace the kind of tool you're looking for:...

I made the original mount a little taller and the ring a little thicker. ... Category: 3D Printer Parts

A lower profile version that suits my needs better. ... Have it mounted on the front of Ender 5.

Mount on left side front before bulkhead of XRT. One screw attached to receiver box. Print from TPU. ...

The sensor wire had gotten stuck in the original part, so I removed the side support and relocated it to the top. Additionally, I drilled out some holes to countersink the bolts on the main supports, ensuring they no longer came loose. ...It was a...

To get it to fit properly, you'll need to peel off the sticky foam from the back of the sensor. I printed the Original Thing with the orientation as shown in the preview, with the base facing down. ...I was worried that the clip parts might break under...

... ...I removed one mount point and clocked the gauge to be orientated properly when hanging from the one mount point. The hole is sized for 10mm diameter magnets. ... I am using a 10mm x 5mm magnet: https://amazon.com/gp/product/B075QYVBJY/

I was in search of a mounting solution and stumbled upon a layer fan I had previously purchased, but couldn't find one that would fit with the original two-piece mount. ...So, I jumped back into Fusion 360 after a decade-long hiatus from using it.

This is a photo eye reflector mounting bracket I made because I could not find one with the correct dimensions online to buy. ...Internal diameter of hole is 1.180"     2.98" height    1.756" length  1.650" wide

End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515 I liked the mount but I have a drag link setup and needed the switch plug facing up

I needed an 18mm mount for this carriage https://www.thingiverse.com/thing:1514245 Fits perfectly. Category: 3D Printer Parts

I replaced my old mounts and they now perfectly match the unique angle of my Toshiba TV's back, significantly improving its overall appearance compared to the outdated adhesive strips that were previously holding it in place.

I tweaked it so that the cutout is at the base and eliminated the servo mount. ...If you're pleased, a tip would be greatly appreciated, as it motivates me to come up with even more innovative designs.

bolt on mount to attach a float switch to water bin/trashcan/tank. should work on any container with a lip 10mm wide or narrower. supports built into design, should snap off easily. ... should print well with no additional supports or such needed...

Mount and display the print directly in front of the fan. You'll find a few 12mm options available, but I opted for this design to avoid using aluminum. ...This is a standard issue Anycubic Kossel Pulley configuration straight from the manufacturer's...

A lower profile version that suits my needs better.I have it mounted on the front of Ender 5.Remixed from https://www.thingiverse.com/thing:4151810