adventurer 3 flashforge 3d models

I've seen some clips for the adv 3 and a glass bed, and it dont work for me. So i designed some edge clips by myself as my very first project on FreeCAD. The glass bed is a 165x165mm plate from ebay seller: https://www.ebay.de/itm/303171068149 ...

This particular adapter will help with the problematic issue of leaving the spool door open due to fitting problems with the standard spool, which does not accommodate about 70% of the spools I have been using.

Spool Adapter for Flashforge Adventure 3 SeriesThis design is a spool adapter for Flashforge Adventure 3. It can be attached to the existing holder to mount regular spools of filament. The connector, with four tapering slots, has a diameter of...

Made this for my Adventure 3 because I replaced the original plate with a PEI plate, so I made the clip with mounting wholes.To be honest, you should printed this on an SLA machine with high temperature resin. If you do it on FLA make sure you print...

Redesign of FlashForge Adventure 3 Bowden Tube Collet I lost my bowden tube collet in a lockdown situation, forcing me to seek an alternative. Since I couldn't obtain a replacement, I embarked on a reverse engineering project to recreate the original...

I just got the updated spool adapter from IrishFrog and customized it myself - this one's specifically designed for Adventure 3 with its four sturdy crossbars, a significant upgrade from the original Tri-Star.

Adventurer 3 でサードパーティ製のフィラメントを外から引き込む為のガイドパーツです。 装着方法 ① テフロンチューブを10cmくらいにカット...

Remix of madsqlj model. ...While the model is spot on it bends over time and is prone to breakage, i reinforced the latch so it can be printed stronger so it does not bend and without supports.

I modified the SpoolHolder_v8 so I could use wider spools such as Amazon Basics brand.

Having used the original spool holder (https://www.thingiverse.com/thing:4002193), after a couple of months it slowly bowed and broke under the weight of 1KG spools. ... I have added a support to take the weight of larger spools.

The original fan blows on one side. Smooth surfaces are wavy, depending on the processing direction. I tried different models and couldn't find a suitable one. With this model it is possible to change the nozzle! The streamers are routed around the...

I wouldn't make a hole into the door to use filament from outside But my door is very simple. That is much much much better! ...;) https://www.thingiverse.com/thing:3419993 or https://www.thingiverse.com/thing:3329107 or ...

This holder spins effortlessly. ... You'll need: 1x M5 bolt, a minimum of 20mm long but ideally up to 30mm 2x 608 bearings Spool specifications include: Maximum diameter: 200mm Maximum width: 80mm (when using the longer bolt) Internal diameter:...

Hello! This is a small piece of plastic that can be placed in front of printing bed to add more support for the flexible plate. In my experience hinge that keep flexible plate in place is pretty weak and does not provide much support, so when...

This remix optimizes the design so less support is needed. Only inside the fitting hole needs to be supported. ...I also tweaked the model a bit so it prints a bit faster.

Diseño 3D por Jesús RamírezMándame un mensajito si necesitas algún Diseño

Unsure if anyone else has this issue, but the left Z axis lead screw was rattling and had a lot of play for me, so this bracket stops that. To install you take the top cover off and undo the 2 screws holding the metal bracket to the case, then lift...

I have modified the factory flexible plate to use a magnetic PEI plate, but my Y-Axis Has been slipping. After several iterations I was able to make this clips that keep the plate from sliding forward. This should be helpful for anyone using...

The Y-axis of the A3 features an 8mm rod with a sturdy carriage gliding on it using brass bushings. The carriage's considerable length makes it unlikely to be the source of the rattling sound. Although the Y-rod itself is not properly secured, it...

Redesigned the fan adapter from moritzrath (https://www.thingiverse.com/thing:4543361) to make room for the fan cable. Also increased the hole size to 5mm to make fitting the rubber holders easier. ... For mounting instructions and parts see:...

Was inspired by Moritzrath's 40mm fan mod. Used the original adaptor for a bit. Had issues after awhile with the fan coming loose and the very thin 30mm tube delaminating when made with ABS. Designed a more robust adaptor that is screwed to the...

Add a lid to the open part of cover Please print the following cover first https://www.thingiverse.com/thing:3184595 The lid is divided into an top side and a bottom side, and the two are connected for use. * Adv3cc_top.stl x 1 The top...

Hello everyone, as some other people already mentioned, the filament touches the spool imo too much with the basic guide - so i created this version of it. ...I haven't printed it yet, feel free to comment and criticize

Set consists of a bracket with which you can mount a 4mm Push-in coupling under the feeder. The hole is 5 mm and M6 thread has to be cut with a tool. For the adapter a hole has to be cut in the door. I have fixed the adapter in the door with some...

This is a remake for the cable management system. I attempted to utilize the original setup but encountered difficulty in removing or installing it without dismantling the entire printer assembly. ...Consequently, I designed this remake and employed...

Made this to save the wear on the tube due the movement experienced without a support.

0.2mm test squares for verifying bed calibration. ...Personally I just choose the best square and align all my prints there in the slicer rather than fine tune the whole bed

This is a remix of the filament guide from underhill. Changed for the 2020-2021 model of which the screw is placed a bit higher. I rebuilt it so the ptfe-tube sits tightly, but can still easily be removed when using the internal spool. For this i...