aem logo 3d models

Each logo includes a 1920x1080p picture that can be used as a desktop wallpaper, and a 3D model of that same logo. For reasons of copyright, and other legalities, these logos are only intended for personal and private use only (CC). I am also...

AEM tru-boost turbo control gauge pod2 pcs assembly Includes: base plate and gauge poduse #6-32 screw & nut for fastener.

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_outline_style = rounded whichextruder = monochrome inner_margin_width = 1 minimal_color_layer_thickness = 0.6 lug_style = plate...

aem ecu

aem cyl

For AEM X 52mm.

s

Customized version of https://www.thingiverse.com/thing:248635 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=248635

Customized version of http://www.thingiverse.com/thing:739573 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options:...

AEM Smart Coil

Dimensionally accurate AEM wideband gauge

Heat_Exchanger_H-AEM step

Model of the AEM smart coil as dimensioned on the AEM website. ... https://www.aemelectronics.com/products/ignition-components/high-performance-coils/high-output-igbt-inductive-smart-coil

AEM dual housing.for air/fuel gauges Update 27/4-14 - better dimensions

Heat exchanger type AEM, high pressure, 4" nozzles for inlet and outlet.

AEM Dual Gauge Pod Sized to fit 52mm Gauge True Size 1:1 scale for real vehicles

The Aem 940 are dual-mode, Diesel-Electric locomotives used by the SBB. The model is made at 1/87 scale and is designed to operate in 2 and 3 rails. Use Ø 0.4mm and Ø 0.6mm brass wire for the railings. ... Material: -1 Bogie Tenshodo center distance...

Hello,Please find the design of Water trap of AEM Electrolyser , If any clarification please let me know , Thanking you, Best Regards, Tarun Kr Dutta

I made this to be able to mount AEM wideband to a gopro suction cup to be able to use in different cars while tuning. I printed using tree supports on print bed only. Print with closed side against bed (180 degree flip from file shown above) use...

I created this for my 2020 Camaro ZL1 1LE to put the AEM AFR gauge in the driver side ac vent. I would print this in ABS to keep the heat from warping the print during the winter months. Leave a comment and let me know how it works out! I...

It's sized for an AEM Wideband / . Failsafe gauge, but will fit over any cylinder. My gauge measures 60.5mm, I sized this to about 59.5 so it will grab a little. It's still a bit loose -- any knock from the outside will bump it out of the way, but...

Customized version of https://www.thingiverse.com/thing:3237206 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3237206

AEM Cold Air Intake Air Return

Gauge extension for AEM Tru-BoostX, sized down to 51mm.

This adapter allows you to mount an AEM UEGO Wideband gauge to a 1/4 camera mount or a suction mount.

Slightly dumbed down AEM 340lph Fuel Pump #50-1000Could also be used as a model for a walbro 255lph universal fuel pump

This is a bracket that allows mounting of AEM 52mm or Similar (Not AEM X-Series) gauges into the location where the factory Performance Pack Gauges will go. Good for gauges that you would like to always have available for view or for passengers to...

Gauge pod for AEM wideband. Has a gopro adapter for use with suction cup mounts. multiple options for orientation with pass throughs for connectors. USE PETG!!!! ...PLA will melt in a hot car.

This design uses the internals of the AEM gauge, and recesses it to be more flush with the dash. It may work for other X-Series gauges, but I don’t have any others to check myself. I have included a comparison picture of the factory vent vs my...

This is a gauge mount for the AEM 30-0300 AFR gauge, although it should work with any 2-1/16" gauge. It was designed to go on my 1978 Chevy C10 on the a-pillar. The gauge ring is adjustable so you can angle it based on your setup. It requires 1 3mm...