air bed inflator 3d models

I was always upset from blowing this inflatable bed. Often after some beers.... I was dizzy :). Now I can take this and enjoy blowing ;) Extra material 1 x DC motor, it's from some toy, probably is only 3V, but it can run at 5V from USB, at least for...

Specifically the 'YAWN Self Inflating Double Air Bed Deluxe' but might fit others, tried and tested on a faulty shop returned unit. Faff to open the motor itself but works a treat. Will need a 2 part epoxy for sufficient adhesion to the motor...

This is an attachment for connecting to air compressor, for inflating tires. It has 1/4" NPT connector commonly found on air compressor hose on one end, and Shrader valve air chuck on the other. Shrader valve is commonly found in the automotive tires...

The locking lever on my Ryobi Power Inflator broke. So I made a new one. Works just like the original. ...Made the spot that broke a bit thicker.

I broke the lever that locks the air hove onto the valve. So I made a replacement. ...Works just like the original.

Replacement for the blue button on the SeaQuest air source BCD inflator.

The mattress has a spring loaded valve that needs to be pushed in with the nozzle of the inflator. it also needs to seal the hole at the same time. the ribbed end pushes the valve and allows air to flow out at the same time. ...its a friction fit that...

A nozzle that should fit most cheap mattress inflators to use it as an air duster. I wanted to stop using compressed air cans and I didn't want to spend $60 for an electric duster. It's a tapered fit to lock on to the inflator. If your printer...

Tip for Leaf blower to inflate swimming pools, air mattress and other inflatables. Fits Toro electric leaf blowers and other leaf blowers. May need a little tape to help hold it on during use. Inflates pools/mattresses FAST! ... Prints fast 43 mins!

Using a DeWalt inflator when camping, none of the tips in came with worked well for inflating my Intex air mattress, which has a self closing valve that can only be pushed in so far. I could not get a decent seal. I modeled this so the standard...

Tip for Leaf blower to inflate swimming pools, air mattress and other inflatables. Fits Toro electric leaf blowers and other leaf blowers. ...May need a little tape to help hold it on during use. Inflates pools/mattresses FAST! Print Settings...

A work colleague needed an attachment to allow him to connect his Makita Blower up to inflate his Air Mattress. There are other designs on Thingiverse similar but I designed this one up from scratch as the Nozzle end was more suitable for the task....

-- [Copied text from previous version](https://www.thingiverse.com/thing:4856717) -- This is an attachment for connecting to air compressor, for inflating tires. It has 1/4" NPT connector commonly found on air compressor hose on one end, and Shrader...

I needed a way to use a bike pump to inflate an air mattress. So I made a conical adapter to a Schrader valve (normal car or bike tire stem). I used ninjaflex to get a better seal but I am guessing pla or petg would work well too since the bike pump...

Ryobi Inflator R18MI has a mattress inflating hose with a short stump of a connector that doesn't fit well in some mattresses. ...This adapter lengthens and increases diameter of the stock connector.</p>

However you may call this thing... ... Maybe use a brim, so it sticks to the bed

Air Sofa Bed, buildt in Marvelous Designer 5 ans exported in Cinema 4D. ...The poached can be hidden.

this inflator has a filling valve a pressure gauge and a venting valve. ...In the sections the air flow is shown.

co2 inflator with 16g cartridge

Replacement clip for inflator. Designed under FREECAD. ... Tested for several months the clip did not deform.

Stent balloon inflator. ...Single handed use prevents agitation of catheter line.

This is a part that adapts a common 15 psi gage available at home improvement stores to to a needle inflator used for pumping up footballs, basketballs, soccer balls... My grandson needed an accurate gauge for his science project where he...

... the same type of mounting to latch onto a garbage bag or similar airtight bag. ... The end has a nozzle sized to fit a Thermarest air mattress, allowing you to quickly fill a seat pad or mattress with very little expended breath and very little time.

The air duct attaches to the laser bed of the Snapmaker A350 to provide air assist and smoke extraction. The duct is designed to fit a 100mm flexible air duct that can be connected to an extraction fan. ... The has slots and holes on the sides to fit...

Modular sofa, armchair and lounge bed: the Claud Open Air collection stands out for its minimal design and soft cushions. Sophisticated and resistant, these furnishings are made of solid iroko with protective varnishing. ...Precious materials and soft...

Modular sofa, armchair and lounge bed: the Claud Open Air collection stands out for its minimal design and soft cushions. Sophisticated and resistant, these furnishings are made of solid iroko with protective varnishing. ...Precious materials and soft...

I made this adapter for the air pump which i have salvaged from the punctured cheap Air-Bed The pump was built-in so i had to cut it out(very simple). Pump can be used for many different things, like another Air-Beds or even I was using it rescently...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=538624 Instructions Using the following options: _line_height = 10 _line_width = 0.5 _spiral_gap = 10 _loops = 5 _bed_type = 120 _bed_y = 150 _bed_x = 150

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=538624 Instructions Using the following options: _bed_y = 100 _bed_x = 100 _loops = 10 _line_height = 5 _line_width = 0.5 _bed_type = 120 _spiral_gap = 5