air conditioner hose 3d models
83397 3d models found related to air conditioner hose.thingiverse
This clamp is designed to attach to the exhaust of an air conditioner. This allows for easy and secure attachment to a window port. This is designed to fit a hose with ridges about 15mm apart from each other when fully extended. The inner diameter of...
thingiverse
This thing is for converting a 6" portable ac hose to a cheaper 4" dryer hose.
thingiverse
I bought a Hisense AP1021TR1GD portable air conditioner but it only comes with a window kit for the dual hoses, while my room has a sliding door. Also I didn't like how close both of the hoses sit next to each other with the original adapter, I...
thingiverse
Simple hose extender for 150mm AC spiral hose
thingiverse
... Fit is very snug, needs a bit of convincing to seat in, but once it's in, there is minimal air leakage. A bit of sealant would make it perfect. ... I modelled this with printing in mind so all overhangs are printable and no supports are needed.
prusaprinters
Accidentally threw the original out and shipping times out here are usually over a week, so instead of waiting I figured I'd make one so anyone else who needs it can have it too. This is a 5.9 inch counterclockwise attachment to connect a tube/hose...
thingiverse
Simple condensation drain hose filter/plug to prevent insects entering the hose. ...Fits Artiplastic 0020TU hose with 20mm outside thread.
cults3d
Simple condensation drain hose filter/plug to prevent insects entering the hose. ...Fits Artiplastic 0020TU hose with 20mm outside thread.
thingiverse
This is a 5-1/4" portable air conditoner/heat pump to 4" dryer exhaust duct. ...I designed this for use with the Black and Decker BPACT14HWT 14k BTU heat pump, but it should be compatible with any left hand thread 5-1/4" hose.
thingiverse
Most stores and online retailers either only offer single hose air conditioners, or those that do offer dual-hose air conditioners charge twice the price for them. I also have yet to see a single dual-hose portable air conditioner that isn't huge...
thingiverse
Exhaust hose connector for Argo Crono portable air conditioner. Joins the 150mm collapsible hose to the rectangular outlet on the back. I'm not sure if it fits other air conditioners; the dimensions of the rectangular end are as follows: Flange width...
thingiverse
Exhaust hose joiner for portable air conditioner - useful for adding an extension if the hose isn't long enough. Suitable for 150mm (6") collapsible spiral tube. Threaded at both ends so you can screw the hose in. ...I printed in PETG as it gets warm...
thingiverse
Purchased an LG Portable Air Conditioner; but, it didn't come with a window kit. ... So, I designed this flange that can be installed into a window cover to vent the AC exhaust.
thingiverse
... wall adapter so I decided to print one! ... Was quite easy to design, 10mm helical thread in a ~5inch tube. Instructions I printed it in white PLA having nothing else on hand, hopefully it wont be too soft at 45-50C when the hot air blow outside.
prusaprinters
Allows the warm air from the air conditioner to be perfectly exhausted through an open window fitted with a window seal. Print:Printer: Anycubic Mega X & Mega SResolution: 0.3 mmBrim: yesSupport: noMaterial: PETGInfill: 100%, less may be...
thingiverse
This is a wall mount collar that fits a 5.9 inch exhaust hose for a portable air conditioning unit. The base was designed to cover a 6.38 in (162 mm) diameter hole drilled in drywall. Most can-light hole saws are about this size. The screw holes...
thingiverse
Inspired by @andreq, I designed and printed this 5.9" version of an A/C exhaust duct connector. This makes it easy to connect two exhaust ducts together. ...I printed in PET, which has worked so far in this high-ish temperature application.
thingiverse
Tested with Daikin system, drain hole diameter 18mm. ... Need small support, only under pipe fitting.
thingiverse
Insect protection for condensate lines. Protects condensate lines from clogging by insects. ... For 18mm corrugated pipe.
thingiverse
I didn't need the inner pipe, so I removed it. ...This made it easier to print without supports, rafts etc.
thingiverse
I created this to hold the exhaust hose for my Danby 14,000 BTU Portable Air Conditioner (DPA140BDCBDB) but it will work for any hose of the same diameter. The idea is to have it attached to an acrylic sheet. (See images) You have two options.
thingiverse
... for other systems and purposes. It consists of three parts. The conduct with an external thread and the integrated connector from wejn (see remix source), the nut to hold the conduct in position and the hose attachment (shortened version) from wejn.
thingiverse
Adapter for mobile air conditioner (exhaust). side A: inside diameter: 125mm side B: outside diameter: 70mm wall thickness overall: 4mm btw: the unclean print on the left side is because of the "crash detection". I disabled it later. ...I read...
thingiverse
The project is to build a box attached to the air intake grid of the AC unit and allowing the connection of a 2nd hose . Due to its size, the box was divided in 4 identical parts. All the parts (box+hose connector) are made of abs and glued (abs...
thingiverse
A remix of https://www.thingiverse.com/thing:6141629 to allow for standard 4" inlet HVAC hose since the HAIER hose is slightly larger.
thingiverse
You all know that portable air conditioners have exhaust hoses to transfer the heat generated by air conditioner to the outside. The idea was to mount exhaust hose through the balcony door plastic blank window (specifically crafted for these...
thingiverse
... which usually have very thick frames. On the connection side, exhaust air hoses in the standard size 150 mm fit, which should be secured with a hose clip. ... The model can be printed without support, but I recommend to print a brim of 10 mm.
thingiverse
I needed a low profile elbow to connect our portable air conditioner hose to a wall outlet. ... It needed to turn 90 degrees and also reduce the 150mm hose to a 100mm connection on the wall