air displacement pipette 3d models
87072 3d models found related to air displacement pipette.
thingiverse
Holder for Finn pipettes / adjustable air displacement pipettes. This fits the pipettes pictured (Eppendorf research plus, Eppendorf reference and Fisher brand). No guarantee it will fit any others. Ours are attached to the wall using Velcro tape...
prusaprinters
This was migrated from my Thingiverse profile and is from 2016.Holder for Finn pipettes / adjustable air displacement pipettes. This fits the pipettes pictured (Eppendorf research plus, Eppendorf reference and Fisher brand). ...No guarantee it will fit...
grabcad
Check out our write-up in BioRxiv: http://biorxiv.org/content/early/2017/02/20/109231
thingiverse
Pipette dispenser for 155mm, 3ml plastic pipettes used for airbrush color mixing or for laboratory applications. ...Holds around 100 pipettes.
thingiverse
All other commercial pipette racks were too large for our crowded lab so I designed this one to keep them neat and tidy.
thingiverse
Customized pipette holder for our shelves, stays on friction alone but adhesive suggested.
thingiverse
<b>Another quite simple laboratory equipment, made on request of my wife, to replace the old and broken one from the store. ... The angle of the pipette from the vertical is ca 15-25 degrees, depends on pipette model.
thingiverse
A simple pipette stand for 4 single channel pipettes (without tips). Made with FreeCAD. ... Instructions Makerbot Replicator 2x Settings: Infill: 10% Number of Shells: 2 Layer Height: 0,3mm
thingiverse
You always wanted that cool Pipette-pen that everyone is talking about? Well this is your chance to 3D print one! ... It will fit a common BIC pen insert.
thingiverse
Hook for hanging DragonLab TopPette brand pipettes- may need some scaling for different brands. ...Just print and attach some double-sided tape on the smaller side to mount on your surface of choice- done!
thingiverse
A spipette stand for multi and single channel pipettes (without tips). Made with FreeCAD. ... Instructions Makerbot Replicator 2x Settings: Infill: 10% Number of Shells: 2 Layer Height: 0,3mm
thingiverse
Needed something to keep the pipette with the jug for the peppermint oil (the jugs don't come with a dropper top), also needed something to cut down drip messes while I'm mixing the wife's e-juice. ...So, I worked this up to clip onto the small jug...
thingiverse
... colour options. I recommend transparent green, it looks great in the lab. Cost of a spool of filament is roughly the price of the least expensive pipette stand out there (that I've found), and you can print multiple copies, over various sizes.
prusaprinters
You can attach this print with a simple cable tie to your chemical and you can always be sure that the pipette is matched with the chemical in the bottle. If the print slides to much you can try to use Ninjaflex as the base for the first layers. I...
thingiverse
I made this for my long airbrush pipettes. I glued the racks to the top piece but left the bottom part loose so I could wash it out when I needed to. ... The uprights were done st 100% as they are fairly thin.
thingiverse
Support for lab vacuum tube to keep aspirating pipettes elevated, two base sizes, one fits a 15mL tube holder and the other fits a 1.5mL microtube stand. ... Use a M4 screw fixed to the "screw cap" to adjust the pressure and hold the tube firmly in...
thingiverse
When i use my airbrush i always have a struggle where to pu my pipette so i designed this small holder . the remaining paint can drip out into the mixing cup. if you make one, please upload a picture. i would like that very much. ... Update: ...