airsoft flashlight mount 3d models
353851 3d models found related to airsoft flashlight mount.cults3d
Flashlight mount for a picatinny rail. I have been using for the past month and it feels great. It works for a flashlight with the diameter of 25mm You will need: 30mm M4 bolt x1 smaller M4 bolt x4 M5 nuts x5 You will need to melt the 30mm bolt into...
thingiverse
Remixed https://www.thingiverse.com/thing:737919 to fit a 25mm to 28mm flashlight also added a Picatinny rail hole for a blot and nut to fit it into place
thingiverse
This is my take on an airsoft trishot shotgun flashlight mount.
thingiverse
This is a flashlight mount that fits onto an airsoft picatinny rail. It holds a 32mm diameter flashlight, and is made to have a snug fit on the rail so that you don't have to use any hardware to secure it. It fits and works well. ... Instructions It...
grabcad
AK74 Flashlight mount for Airsoftdiameter of the light aperture 28,5mmmaterial PTG
grabcad
Helmet Flashlight mount for Airsoftdiameter of the light aperture 28,5mmmaterial PTG
thingiverse
In need for a pressure switch mount for my airsoft replica, i designed and printed this. 85 mm long and it fits on 22mm rail. I printed this with ABS because it is strong and it will not break. I will sand it and paint it in black. ...
cults3d
In need for a pressure switch mount for my airsoft replica, i designed and printed this. 85 mm long and it fits on 22mm rail. I printed this with ABS because it is strong and it will not break. ...I will sand it and paint it in black.
thingiverse
# Flashlight quick lock mount A picatinny mount to hold a flashlight while allowing to quickly remove it from the mount. I have a flashlight mounted on my rifle, and sometimes want to use it without pointing the rifle everywhere. This design was...
thingiverse
... rails to the front to facilitate a flashlight, in my case the Streamlight TLR-7A. I can ONLY vouch that it fits this flashlight, I have not tried other similar style lights on it yet. ... Original credit to -FMDA1776 for the mag holder design.
thingiverse
I've uploaded two variations of this mount, one that where the light is angled down over the magazine and another that keeps the flashlight tucked up against the body - depending on if you plan to use a remote switch or not, one design may make more...
thingiverse
I modified the source to have a small channel to allow it to clamp my rail better and re-sized it to fit a ~24 mm Streamlight©.
thingiverse
... Видео урок по сборке можно посмотреть тут: https://youtu.be/n3mr-GlDEWw __________________________________________________________________________ Hello! I present to your attention a project to create a pistol flashlight (for airsoft)
thingiverse
A flashlight holder for Airsoft or Nerf. It's a simple one piece design, no screws or glue. The track is a friction-fit, and the flashlights snap in. The flashlights I'm using are from Harbor Freight. They are pretty bright though so I won't...
thingiverse
designed this for a cheap flashlight with an outer diameter of 1 inch. ... enjoy!
thingiverse
Works with a flashlight with a belt clip (around 35 - 45 mm long) and a (recommended) diameter of 28mm (battery holder - handle - NOT the light bulb container). You also need 2 m3x30mm screws and m3 bolts. Funziona con una torcia con un aggancio...
thingiverse
GO here for the Flashlight scope mount for 40mm scopes Will add link at later time. ... Flashlights with 1in(25.4mm) to 1 1/4in(31.75) handles Reguired items 6 6/32 bolts 6 6/32 nuts RECOMMENDED for Flashlights with ZOOM Download these stops to prevent...
thingiverse
Flashlight mount for light with tube OD 25,4 mm ( 1 inch) Inside is the M4 thread
cults3d
Flashlight mount for light with tube OD 25,4 mm ( 1 inch) Inside is the M4 thread
thingiverse
Mount for flashlight Nitekore HC-50 on a bicycle, calculated under the steering wheel 32 mm the mount is attached to the bike with two cable ties
thingiverse
Allows you to hold a flashlight with a tripod mount 20180311 Version 2 Added Knurling for better grip Head "neck" increased in diameter for more strength
thingiverse
Flashlight mount, M3 nuts&bolts, elastic cord Print Settings Printer: Trinus Rafts: Yes Supports: No Resolution: 0.15 Infill: 25 Notes: Black eSun PLA printed at 195°C, 80% fan speed, heated bed at 55°C, 40mm/s How I Designed This Looking for a way...
thingiverse
The Yifeng is a very common flashlight sold under many names. ... One end is recessed to accept a wafer magnet but it also has a counter-sunk hole so it can be screw mounted.
cults3d
I got tired of not finding my big flashlight when i need it, it always being in the way when i didn't need it. ...so i made a c shape clamp to mount it above my bottom bunk.
thingiverse
I got tired of not finding my big flashlight when i need it, it always being in the way when i didn't need it. ...so i made a c shape clamp to mount it above my bottom bunk.