airsoft scope rings 3d models
192244 3d models found related to airsoft scope rings.thingiverse
Small picatinny rail scope ring mount to attach a cheap red dot (https://www.amazon.com/dp/B00A36MKUO) to a cheap compact 3x-9x scope (https://www.amazon.com/CVLIFE-Compact-Crosshair-Reticle-Shooting/dp/B073QM8FP9/) or even cheaper full sized 40mm...
thingiverse
Since the S&T mount uses proprietary rail dimensions these wont fit standard rails without modification to the 3D file . Screws are M3 x 8mm, 4 screws per mount. ... Be sure to post "Makes" if you print, makes me feel all warm and fuzzy ^^ ...
thingiverse
- For the scope ring that doesn't have a rail go to his page for that file (https://www.thingiverse.com/thing:5428968), as I made no modifications. ... - Added a variation of the scope ring that has a picatinny rail section for mounting a small red dot...
thingiverse
This is a scope for airsoft that I am printing for my friend who does not want to spend money on an expensive scope.
cults3d
These are 2 sizes of 3d models that can slide onto your airsoft scope and reduce the glare on your scope with can improve aim and accuracy but also reduces your visibility as the shine from the glass is reduced. Included are 2 sizes of flash hider...
thingiverse
Protect your expensive sights/scopes with this two part airsoft protector! Designed for M3 Screws, either brass knurls or nuts Works with any thickness polycarbonate sheets, tested with 2mm and 4mm. ... Recommend printing in PETG
thingiverse
Here is a scope mount protection for our airsoft scope. After having broken my 2 plexiglass protections (those sold with the picatinny mount), i needed to design this piece to mount another cut plexiglass sheet. Now i can replace it if I broke it. ... ...
cults3d
This knob can be used with airsoft scope in order to tune the adjustments without removing the original cap. Just remove the original cap and use the original screws to fix this printed item. ... In order to work properly find the center position of...
cults3d
Scope extender for a 47mm scope. This item goes over the scope about 28.5mm and out of it ~50mm. ...(see the picture)
thingiverse
this scope is facsimile from russian okp7,since I dont have one ,the size of this scope is basicly copied from pictures and it might not be accurate things follow are required m4*30screw* 1 m4nut*1 m3*5*11 m3*6*3 m8*8/m8*10 set screw*2 0.7*7*10...
thingiverse
I designed this mount for the Cyma cm032(M14).This is as low as the scope gets without modifying the rear sights.For it to work your scope small diameter need to be 26mm. ... You need: -4pcs M4x16 screw -4pcs M4 nut -1pcs M5x12 screw 1pcs M5...
thingiverse
I purchased the scope and mounting hardware for the DBoys at the time but found it did not fit my new skirmishable Kar98K which was made by Matrix: Matrix Mauser Kar 98K WWII German Infantry Bolt Action Service Rifle...
thingiverse
This sight protector is designed for airsoft use only. It is friction fit over a red dot sight. It was designed for a cheap Chinese sight that I got off amazon. ...Should work for any sight that has a 40mm OD It needs a 40mm diameter circle piece...
thingiverse
Airsoft SVD side Scope mount. ...4 screws needed to assembly
thingiverse
HI, Some 80mm scope rings... This is a bit of a remix as i used portions of the piggyback tube rings by Bagna97 and modified them. Fits great on my ST80 tube. All holes are for 6mm bolts. ... I added a bit of cloth tape on the inner surfaces to...
thingiverse
Rings for guide scope mounting on main telescope bar. You need print these parts: ring (+ mod) 2x bar_holder 2x knob 6x cap 6x Parts are printed from PLA with 70% fill. Modifier for rings are 100% filled. The caps are printed from flex fillament. ...
thingiverse
This is a Finder Scope Ring set with a standard dovetail (I think the right name is SB0800, but not sure. If you know and want to comment, please feel free!). I made this for my Celestron 9x50, that has an external diameter of 53mm. Should work ok...
cults3d
This is a Finder Scope Ring set with a standard dovetail (I think the right name is SB0800, but not sure. If you know and want to comment, please feel free!). I made this for my Celestron 9x50, that has an external diameter of 53mm. Should work ok...
thingiverse
Third test for these scope rings, attempting to hold a red dot optic in place on a Crossman F4 Nitro Piston Pellet Gun. -expanded inner hold -merged outer and inner bases -shortened height -other minor cosmetics Testing at 80% infill at .2 ...
thingiverse
... for SW 72 ed telescope to hold guiding scope and camera. ...Setup in photo is rev.1. Rev.2(silver one), gives more room for the plastic nut that comes with the scope and is pushed a bit forward to help with balance since this scope is back heavy.
thingiverse
For Airsoft use, killflash with 48 mm diameter, 0.8 mm honeycomb thickness, 2 mm outside ring thickness
thingiverse
For fun, and as a bit of a joke, I decided to make a scope mount for a cheap (like £20) airsoft pistol I bought many years ago. I then put a cheap (~£11) red dot sight on top of it I bought from AliExpress **You will need:** - 5 M3x10 screws ...
thingiverse
As material, you need : - A Mobius 2 action cam, with its long range lens - A longer 24p flex cable (mine is 20.1 [cm] long) - A x50 opening scope, threaded on front - A cylinder battery bank, based on 18650 battery (optional) - Some 2.5 [mm]...
thingiverse
scope hinged mount you will need once you print it off 6mm pin about 50 mm long i used a 6x50mm bolt and cut head off also need 3 3x20mm allan bolts or what ever you wish to use but no longer than 20mm otherwise it will hit the hinge and the flip...