ak clamp on front sight 3d models

The artwork depicts an object that could be used in-game. ...Four maps are available for this object: normal, gloss, reflectivity, and albedo.

Very simple, fast print.

Printed at one point zero five percent larger than standard size.

Designed in Tinkercad. ...Printed successfully in Monoprice PLA+ 999 bottom layers 0.12 resolution

Designed in Tinkercad. ...Printed successfully in Monoprice PLA+ 999 bottom layers 0.12 resolution

I was on a mission to optimize my somewhat quirky setup when a brilliant idea struck me - creating a flexible system that would allow me to adjust the feed direction and guide as needed. My primary concern was preventing the gantry from getting too...

On my balcony, I quickly realized that there was no feasible way to repair the wooden fence against the railing. ...Instead, I got creative and came up with a makeshift solution.

Attach a sturdy 13 mm irrigation hose with a simple nail-on clip that's built to last. To secure it, you'll need a 1.5 to 2 inch flat head nail - a must-have for a reliable installation. I created this design to outperform flimsy commercial clips...

Most cheap break-barrel air rifles suffer from a different point of impact whenever you close the barrel, this allows me to avid that issue, since the scope is mounted on the barrel therefore should always point to the same place as the barrel...

This customized item is based on the design at http://www.thingiverse.com/thing:135771 and was created using Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=135771). The specifications for this version include a thickness of 2, a...

I'm using 6 mm ID cable clamps, one screw and one glue - a powerful combination to keep my InMoov's wiring tidy. ...I've paired them with this innovative spiral wire wrap:...

Customized version of https://www.thingiverse.com/thing:62800 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=62800

I discovered that the original hex recess was undersized for the required 8-32 nut, so I modified it in Fusion 360 to provide just enough clearance for the 11/32 hex nut.

The "Front Lock Ring" of the Rapido Clamp is just a 77-82mm step-up ring. The outer diameter of this ring is very small, so it is often stuck to the Outer Ring. If it happens on set, it would be a nightmare... So I designed this model to rotate...

This custom front fork brake hose clamp was specifically designed for my 2013 Beta 300RR enduro motorcycle. ...It incorporates the iconic Beta brand logo to enhance its visual appeal.

To attach my front S53 fender to the Enduro SWH fork I have modeled and printed this clamp bridge. ... I glued two layers of tape / scotch tape in the clamp, so that it fits better to the tube of the fork.

Remixed from https://www.thingiverse.com/thing:2076034 Just changed it so cords can be hung from the front instead of the back.

This item is designed to attach a simple bicycle light.\r\n\r\nThis product is manufactured with: REAL-Filament's Black PLA 2.85mm filament.\r\n\r\nSlicing software used: Cura.\r\n\r\nPrint Settings\r\n\r\nPrinting quality:\r\nLayer thickness: 0.15...

You can either keep your specter M4 front wired or rewire to rear, I removed the block on mine and cut a spring guide down and inserted and glued the back section in the block to act as a nut for a buffer tube screw then made a hole so the wires...

No information is available about this individual.

Featuring lenses with a film capable of capturing side projections, the blue buttons enable you to switch off the projectors while the tiny red lenses, also functioning as projectors, complete the picture. ...This innovative concept can be connected via...

Front sights for Nerf guns with top accessory rails work perfectly on my accessorized Modulus Mediator, which also features a bayonet bracket I designed that can hold 2 darts. This sight is an excellent addition to my blaster collection. ... The small...

Very useful!

A simple little shelf to attach to a windowsill. Has thumb screws to hold it in place. ... Opening is 20mm wide and 18mm deep.

This is a Fence designed to fit over an existing Link Fence, avoiding having to dig to insert new posts, don't have to remove the old fence (providing that is still in good condition). Its perfect for the individual, that just wants to add more...

HV-B||-1000

For Kawasaki ninja 250RR 2011-2012, T6 material, the triangle is still using standard shock. ... rendering using KeyShot 3

This design was created using Tinkercad. ...It can be edited live at ttpswwwtinkercaddocomththings3XkwpILtnF5