ak dust cover rail 3d models
190611 3d models found related to ak dust cover rail.cults3d
Dust Cover AK with Picatinny Rail Fits Cyma /LCT etc https://creativecommons.org/licenses/by-nc-nd/3.0/
cults3d
RIS rail for AK Dust Cover (receiver cover plate). Modeled for installation on Kalashnikov airsoft guns from Cyma and LCT series AK47, AKM, AK74, AK105 / 104 . To install, you will need : 1. 22mm screw, I used a screw without a washer for the inner...
cults3d
RIS rail for RPK / AK Dust Cover (receiver cover plate). Modeled for installation on Kalashnikov airsoft guns from Cyma and LCT series RPK74 AK47, AKM, AK74, AK105 / 104 . To install, you will need : 1. 22mm screw, I used a screw without a washer for...
cults3d
Replacement dust cover button for airsoft AK. ... Test fitted on Cyma AK's, should fit most brands.
thingiverse
Replacement dust cover button for airsoft AK. ... Test fitted on Cyma AK's, should fit most brands.
thingiverse
AK Spring Tensioner for a CYMA AK74. ...I tend to break these little pieces so I made one to replace the broken one.
thingiverse
Snapmaker 3-in-1 Original Y-Axis Linear Dust Cover This is a 3D model for people using the initial model of Snapmaker 3-in-1 Original (2.0 is not eligible). When the Y-axis is used for cutting, etc., dust can get into the Y-axis rail and cause it to...
thingiverse
... you'll need to remove the scope rail and use those screws to secure the cover. the pictured version is the long with personalized text, the available models are blank. must be printed with supports, best results with the rails oriented down.
thingiverse
The AK Betaz Spetznaz has no rail for a red dot of any sort. So decided to create a for end upper with an integrated rail. Has a slot in the rail so iron sights can be be still used. Print with the rail side up and supports, should just slide on...
cults3d
If you want to had accessories to your AK AirSotf replica but you are stuck with the original furniture you can swap for this models that have Picatinny rails. ...With the download you get two models, one of the upper part and one for the lower part.
thingiverse
This is a part to hold the rails in the AK at the right height while you do the first spot welds. The side with the indent is for the ejector rail. Assemble as shown in the photo (The notch cutout for the thicker rail has moved from the middle piece...
thingiverse
Airsoft AK adapter Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: No Supports: No Resolution: 0,2 Infill: 60-80%
thingiverse
I didnt't print it myself so only attaching results. Tested on Cyma AKSU cm035a. Fits well, not tight but ok. Might be adjysted by shaping "wings" because this detail can't be pulled out without pull out of the spring guide but anyway it works. ...Can...
thingiverse
AK-74 muzzle dust and dirt protection cover https://www.tinkercad.com/things/9MDiDINgBr0-ak-muzzle-cover
thingiverse
The rail sight & cover would slide off the Stryfe rail, so I remixed a file and made a strip to help secure it. You need to super glue a strip on each side of the rear rail to make it wide enough for the cover. ... Original file can be found here...
grabcad
Cover for AK-47 with Picatinny rail. This is only a concept. ...A handle to mount the rotating bolt will be added but I still am working on it.
thingiverse
AK rail adapter V2 to scope Print Settings Printer: Prusa I3 plus Rafts: No Supports: No Resolution: 0,2 Infill: 60-80%
thingiverse
Refined AK charging handle cover, fits standard m2 nut and screw. ...Should fit most AK's, designed to fit on psak-47 gf3.
thingiverse
I couldn't find a way to screw the rail mount on my ak airsoft. The rail mount itself is here: https://www.thingiverse.com/thing:777866 I designed an alternative for the little piece that holds the rail mount on the rifle. ...I designed the hole pretty...
grabcad
One of my first designs for AK rail system. Three Picatinny rails on bottom part and one on the top. Should fit most models thanks to "barrel clamp" mounting. Upper parts has two versions; with standard and expanded top rail. Designed for CNC...
prusaprinters
This is a Picatinny rail for my AK-47 airsoft you do need to make 2 4mm holes in the top and bolt it on with 4mm bolts and nuts. ...I printed this with ABS.</p><p>Buy me a coffee: https://www.patreon.com/muxoid </p>