ak slr handguard 3d models

Reverse modeling of JINGJI SLR gelblaster model handguard.

This small piece replaces the spacer that sits under the top rail in the handguard, and slides into a small hex shaped hole in the receiver when assembling them to stop the handguard from rotating, and inadvertantly undoing the barrel nut. ... Id...

Tactical front handguard on AK airsof

Tactical front handguard on AK airsoft.

Tactical front handguard on AK airsoft.

A hexagon handguard kit for AK, fits like a zhukov front handguard. ... -to mount it properly print 2 clips

CAD model for the handguard of the AK-100 Series rifle.

Handguards for the yugo pattern ak. ... One with a grip and one normal

Handguard for AK BETA by brand CYMA.Tested and modeled on very old CYMA, type CM.029-01A, its AK beta.

Tactical front handguard on AK airsoft If you need corrections, contact us via the group: https://vk.com/big_gun3d

Tactical front handguard on AK airsoft. ... If you need corrections, contact us via the group: https://vk.com/big_gun3d

Tactical front handguard on AK airsoft. ... If you need corrections, contact us via the group: https://vk.com/big_gun3d

This one is SLR ak like SLR Ak Grand Thumb owned Check out full album of my SLR ak here https://www.facebook.com/pg/Guzshop/photos/?tab=album&album_id=903666296713147

This is the handguard of the classic Ak47 for Airsoft replicas. ...This model is also compatible with other Ak type replicas.

https://www.apexgunparts.com/ak-laminated-handguard-set-brown-nos.html I modeled up some spacers to make the handguard a snug fit. The rear spacer slides into the front of the receiver. There's no need to glue it in. The front spacer sandwiches...

Bought a red dot for my airsoft ak and wanted to mount it and realized that there are no handguards so decided to make one Print at 100% infill and default orientation, enable supports

this is a handguard addapter too allow fitment of a m4 handguard to the jinming j11 ak print threaded end up. There's a small sight rail on top to suit a small red dot. is also designed with a m4 outerbarrel in mind. No support required except for...

A friend of mine was complaining that the stock on his SLR AK was to short and was lacking a cheekrest i made 2 files one low and one high

AK 200 series inspired handguard, since i work only with pictures might not be 100% accurate. I managed to fit it on my Cyma AK 74, note the fact that different manufactures use slightly different dimensions for gas tubes, for example i was not...

AK 200 series inspired handguard, since i work only with pictures might not be 100% accurate. I managed to fit it on my Cyma AK 74, note the fact that different manufactures use slightly different dimensions for gas tubes, for example i was not...

A basic spacer for the front handguard of AKM/AK74 style rifles. ...Will not work on AKS74U.

3d printed model for airsoft AK in style of Troy industries and escape from Tarkov

This is the quad rail setup on my AK model. ...Upper, Lower, 4 Rail Covers, and 4 Screws.

pin that holds front handguard in place very tight fit but it works you may need to hammer it inside also dont put it all the way in leave 1mm clearance print it flat so its strong

-= Русский =- Кастомная нижняя ствольная накладка на Автомат Калашникова (ак, ак47, ак74, акм и остальные схожие модели) -= English =- Custom lower barrel pad for the Kalashnikov assault rifle (AK, AK47, AK74, AKM and other similar models)

-= Русский =- Кастомная верхняя ствольная накладка на Автомат Калашникова (ак, ак47, ак74, акм и остальные схожие модели) -= English =- Custom upper barrel pad for the Kalashnikov assault rifle (AK, AK47, AK74, AKM and other similar models)

-= Русский =- Кастомная нижняя ствольная накладка на Автомат Калашникова (ак, ак47, ак74, акм и остальные схожие модели) -= English =- Custom lower barrel pad for the Kalashnikov assault rifle (AK, AK47, AK74, AKM and other similar models) Category:...

If you want to had accessories to your AK AirSotf replica but you are stuck with the original furniture you can swap for this models that have Picatinny rails. ...With the download you get two models, one of the upper part and one for the lower part.

-= Русский =- Кастомная верхняя ствольная накладка на Автомат Калашникова (ак, ак47, ак74, акм и остальные схожие модели) -= English =- Custom upper barrel pad for the Kalashnikov assault rifle (AK, AK47, AK74, AKM and other similar models) Category:...

AK-47 M17 VALKEN HANDGUARD